Yamaha rx v10

Page 1

AV RECEIVER

X-V1OMK II

SERVICE MANUAL

IMPORTANT NOTICE

This tnanital has been provided tor the tise ot authorized YAMAHA Retailers and their serVice personnel.
it has been assumed that basic serytce procedures inherent to the iriditstry. and more specifically YAMAHA
Products. are already ltnotyn and understood by the users. and have therefore not been restated.

WARNING: Failure to tollow appropriate service and safety procedures when seryicing this product
may result in personal injury. destruction of expensive components. and failure of the
product to perform as specttied. For these reasons. we adyise all YAMAHA product
owners that atiy seryice required should be performed by art authorized YAMAHA
Retailer or the appointed Sen ice representative,

IMPORTANT:The presentation or sale of this manual to any uidiyidual of firm does not constitute
authorization. cerilflcailon ot- recogiiinon of arty applicable technical capabilities.
or establish a pniiciplefilgenl relationship of any form

The daia proVIded is believed to be accuraie and applicable m IIie fluids) indicated 0 the cover. The research.
engineering, and service depai1iiiems of YAMAHA are continually sti-iyinp to improve YAMAHA ptodttcts.
Modificaiions are. Ilielefnre. Inevitable and specificailoiib are subject to change wlihollt noiice or obligaiioii
[0 retrofit Should any discrepancy appear to exist. please coriiaci the disiribuiork Service Division.

WARNING: Static discharges can destroy expensive components. Di your body may have accumulated by grounding youi'selfio the ground buss in the unit
(heavy gauge black wit-es connect to this buss).

IMPORTANT: Turn the unit OFF during disassembly and part replacement, Reclieclt all work before
you apply power in the mill,

I CONTENTS

TO SERVICE PERSONNEL 1
REMOTE CONTROL PANEL 1
FRONT PANELS 2
REAR PANELS 3
SPECIFICATIONS....................................................... 4~5
INTERNAL VIEW 6
DISASSEMBLY PROCEDURES 6
SELF CHECK MODE 7~9
AMP ADJUSTMENT 10

Lmvitxvzlrmi. 1377733E®§$fli€l§m bTuifs
TI'HS Service Manual uses recycled paper

100656

TUNER ADJUSTMENTS 11~14
IC DATA 15~20
DISPLAY DATA 21
BLOCK DIAGRAM 22~25
PRINTED CIRCUIT BOARD 26~39
SCHEMATIC DIAGRAM 40~43
PARTS LIST 44~55
REMOTE CONTROL TRANSMI'I'I'ER 56

.YAMAHA

YAMAHA CORPORATION
P.O.Box1.HamamaIsu.Japan

Page 2

RX-V1OMKII

I TO SERVICE PERSONNEL

1. Critical Components information.
Components having special characteristics are marked and
must be replaced with parts having specifications equal to
those originally installed.

2. Leakage Current Measurement (For 120V Model only).
When service has been completed, it is imperative that you
verify that all exposed conductive surfaces are properly insu-
lated from supply circuits.

0 Meter impedance should be equivalent to 1500 ohm shunted
by 0.1 SHF.

O Leakage current must not exceed 0.5mA.
0 Be sure to test for leakage with the AC plug in both polarities.

WALL
OUTLET

(ID

:D-

AC LEAKAGE
EQUIPMENT TESTER OR
UNDER TEST EQUIVALENT
<-
INSULATING
TABLE

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition. other electrical/electronic and/or plastic (where
applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly
other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON

WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes

to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling

food.

I REMOTE CONTROL PANEL

YAMAHA