Yamaha htr 5063

Page 1

AV RECEIVER

RX-V567/HTR-5063

SERVICE MANUAL

/

WARNING: Failure to follow appr

IMPORTANT he presen n or sa
cognition any appli
The d ovided lie
partmen f YAM
pecifications subje
tributor's Se e Divi

RNING:

be accurat
A are c

This manual has been provided for die use ofaufllorized YAM HA Retailers and
It has been assumedtliat basic service procedures inner
and understood by the users, and have therefore not been ted
e service and
destruction of expens co

all YAMAHA produc whers
the a service r esent
this manu to any individual or firm does not constitute authorization, certifiCation or
e technical capabilities, or establish a principle-agent relationship of any form

(1 applicable to the unit(s) indicated on the cover The research, engineering, and service
ally striving to improve YAMAHA products Modifications are, therefore, inevitable and
change wimout notice or obligation to retrofit Should any discrepancy appear to exj st, please contact the

Static discharges can destroy expensive components Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss)

IMPORTANT NO CE \

r service personnel

0 the industry, and mor ecificaiiy YAMAHA Products, are already known

ty procedures when servicing this product may result in personal injury,
re ofthe product to perform as specified For these reasons, we advise
equired should be performed by an authorized YAMAHA Retailer or

n ants, and
any serv

\IMP RTANT: Turn the unit OFF during di sassembiy andpan replacement Recheck all work before you apply power to the unit /

I CONTENTS

TO SERVICE PERSONNEL ............................................ 2
FRONT PANELS
REAR PANELS ..................
REMOTE CONTROL PANEL ..
SPECIFICATIONSlfifitfli

INTERNAL VIEW .................................... ...15
SERVICE PRECAUTIONS I fi- Exnsaagfi$13 ..... 15
DISASSEMBLY PROCEDURES r mafia ........... 15-13
UPDATING FIRMWARE!

7; -Li'7:?0)%i9iaas ..................................... 19-32
SELF-DIAGNOSTIC FUNCTION 1

52x72? magnifies) ....................................... 33-64

:md-Ez-r::.71lzhtl I :I'v- fiatmfiyfififififi LCinsen
Thls Servlna Manual uses recycled paper.

DISPLAY DATA ....................................................... 65-66
IC DATA ....................................... 67-76
PIN CONNECTION DIAGRAMS . 77-79
BLOCK DIAGRAMS .............. ..80-83
PRINTED CIRCUIT BOARDS .. 34-101
SCHEMATIC DIAGRAMS ........ .103-114
REPLACEMENT PARTS LIST . 115-133
REMOTE CONTROL .. 134-137
ADVANCED SETUPI'. 138-139
AcfiwéfiEEiEEaz, .......................................... 140-141

101170

Copyright© 20l O YAMAHA mam All rights reserved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically Without permission

.YAMAHA

YAMAHA CORPORATION

POBUX 1, Hamamalsu, Japan
10.04

I
l
<
I
a)
g
_|
:F
01
D
m
w

Page 2

0')
(D
O
P
D:
I-
E
[x
(D
LO
?
X
I

RX-V567lHTR-5063

I TO SERVICE PERSONNEL

1. Critical Components Information
Components having special characteristics are marked A and
must be replaced with parts having specifications equal to those
originally installed.

2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.

0 Meter impedance should be equivalent to 1500 ohms shunted
by 0.15 uF.

For U model
IE3 CAUTION

AC LEAKAGE
WALL EQUIPMENT TESTER OR
OUTLET UNDER TEST EQUIVALENT

®2D-

J:

INSULATING
TABLE

0 Leakage current must not exceed 0.5mA.
0 Be sure to test for leakage with the AC plug in both polarities.

-A-V "E3701: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 6A,

125V FUSE."

For C model
CAUTION

F3701: REPLACE WITH SAME TYPE 6A, 125V FUSE.

ATTENTION

F3701: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 6A 1 V,

WARNING: CHEMICAL CONTENT NOTI E!

This product contains chemicals known to the St of Cali

harm.

nia t use cancer, or birth defects or other reproductive

DO NOT PLACE SOLDER, ELECTRICAL/ELE TRONI OR PL TIC COMPONENTS IN YOUR MOUTH FOR ANY REASON

WHATSOEVER!

Avoid prolonged, unprotect
expose eyes to solder/flux vap

contact

twee solder and your skin! When soldering, do not inhale solder fumes or

If you come in contact with sold or com onents located inside the enclosure of this product, wash your hands before

handling food.

About lead free solder/ antes; \yfiIE'DLT

All of the P.C.B.s installed in this unit and solder joints are
soldered using the lead free solder.

Among some types of lead free solder currently available,
it is recommended to use one of the following types for
the repair work.

0 Sn + Ag + Cu (tin + silver + copper)

0 Sn + Cu (tin + copper)
. Sn + Zn + Bi (tin + zinc + bismuth)

Caution:
As the melting point temperature of the lead free solder
is about 80°C to 40°C (50°F to 70°F) higher than that of
the lead solder, be sure to use a soldering iron suitable
to each solder.

$%K%fi$hfm6?&T®EW£$0Ayfifium
cheese urea/1w \yéic/ \ysiivtltihfviaz
fiflflyfiufim HTE®$5Efifinyfiwfifiéfifibido

. Sn+Ag+Cu (E + E + Eli)

- Sn+Cu ($%+§Ifi)

- Sn+Zn+Bi as + fits + EXVX)
fig:
sew \y aoateialeaaeeoeax U / \y mitt/s 30 ~
mTEEE 73 \y 91??? stifle < fairy»