Yamaha dsp ax1800

Page 1

AV RECEIVER/AV AMPLIFIER
RX-V1 800]HTR-61 90/

DSP-AX1 800

SERVICE MANUAL

/

contact the distributor's Service Division.

\

I CONTENTS

TO SERVICE PERSONNEL .......................................... 2
FRONT PANELS ........................................................ 3-4
REAR PANELS .......................................................... 5-8
REMOTE CONTROL PANELS 9
SPECIFICATIONS I éfilfli ................................ 10-1 3
INTERNAL VIEW ......................................................... 14
DISASSEMBLY PROCEDURES I fififllfi... .. 14-20
UPDATING FIRMWARE /

77-A017wgfifla ..................................... 20-33
SELF-DIAGNOSTIC FUNCTION /

5M 77 (a Batman ..................................... 34-70

:aw- Ex 7:17M1. :27-732Ofi1isma Wins-Ia,
This Service Manual uses recycled paper.

IMPORTANT NOTICE

This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users. and have therefore not been restated.

WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury. destruction of expensive components. and failure ofthe product to perform as specified. For these reasons.
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.

lM PORTA NT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition ofany applicable technical capabilities, or establish a principle-agent relationship of any form.

The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering. and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore. inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please

WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
llVl PORTA NT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

\

/

AMP ADJUSTMENT/ 7>7fifisa§ ........................... T1
DISPLAY DATA ........................................................... 72
IO DATA ................................................................. 73-84
BLOCK DIAG RAMS .............. 85-87
PRINTED CIRCUIT BOARDS .............................. 88-115
PIN CONNECTION DIAGRAMS ........................ 116-118
SCHEMATIC DIAGRAMS .................................. 119-137
REPLACEMENT PARTS LIST .......................... 139-174
REMOTE CONTROL .......................................... 175-173
ADVANCED SETUP I

TIFIwZFtv b7v7fi:1- EfiETé ..... 179-181

II
2
35
'93
a2
1
---|
3."
CD)
a
t9
2

Page 2

B
a:
\-
98
E00
-
RE
8:
was
-
>0

RX-V1800/HTR-6190IDSP-AX1800

I TO SERVICE PERSONNEL

1. Critical Components Information
Components having special characteristics are marked A
and must be replaced with parts having specifications equal
to those originally installed.

2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.

0 Meter impedance should be equivalent to 1500 ohms shunted
by 0.15uF.

For U model
IE3 CAUTION"

AC LEAKAGE
WALL EQUIPMENT TESTER OR
OUTLET UNDER TEST EQUIVALENT

®=D-

J.-

INSULATING
TABLE

0 Leakage current must not exceed 0.5mA.
0 Be sure to test for leakage with the AC plug in both polarities.

*Aiv F1, F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE

10A, 125V FUSE."

For C model
CAUTION

F1, F2: REPLACE WITH SAME TYPE 10A, 125V FUSE.

ATTENTION

F1, F2: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 10A, 125V.

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where
applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and
possibly other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solderfumes or expose
eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure ofthis product, wash your hands before

handling food.

About lead free solder / fifi'fifl / 5513) b \C

All of the P.C.B.s installed in this unit and solderjoints are
soldered using the lead free solder.

Among some types of lead free solder currently available,
it is recommended to use one ofthe following types for the
repair work.

- Sn + Ag + Cu (tin + silver + copper)
- Sn + Cu (tin + copper)
. Sn + Zn + Bi (tin + zinc + bismuth)

Caution:
As the melting point temperature ofthe lead free solder is
about 30°C to 40°C (50F to 70CF) higher than that ofthe lead
solder, be sure to use a soldering iron suitable to each solder.

Zfifillfiflé fitméjKTUDEWEaZUV \JQHUICCIZZDES
fifilififiu} \751) \JSfiljéitfmido

fificu \yfil Claw) < DbODtifibiafi 0 i373)» IlgfiflallliFEECD
a: 5 Hfin} \JfiODIQEflEfifi [Li-99

- Sn+Ag+Cu (i%+§tE+filfil)
' Sn+Cu($%+$Ifi)
~ Sn+Zn+Bi(§%+fi~a+E7\77\)

3%? 3
fificl) \Jfimflfiéfifglififidfifikbl \JQICI:I3/\SO~4D°C
EEE< Katmifidfd %11%TLOJJ \yfillé'flt/ VJ?
C'CEEQEEH < Esme