Yamaha cd1330

Page 1

MICRO COMPONENT SYSTEM MCS-1330

CD PLAYER

CD-133O

SER E MANU

The MCSe1330 consists Of the R4330, CDe1330 and NSeBP400.
This service manual is for the CDe1330.
For service manuaI of the R1330 and NSeBP400, please refer to the foHowrng publication number:

Re1330/NSeBP400:

M64 330 EL RaI330c CD71330 EJU NSsBP400 Tfifiiithi-fi
ZUJfi- (77:1 7AA: CD7133O PET-95,
R-1330\ NS-BP4OO %®#- 817: 17)inTEE§Ef7/Y-E%fifi L? < T5390

R71330/NSsBP4OO:

IMPORTANT NOTICE

This manual has been provided tor the use of authorized YAMAHA Retailers and their seryice personnel,
II has been assumed that basic service procedures inherent to the industry. and more specifically YAMAHA Products. are already known
and understood by the users. and have thetetore not been restated,

WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury.
destruction Ofexpensive components. and tailure of the product to perform as specified. For these reasons, we advise
all YAMAHA product owners that any service I'quIII'ed should be performed by an authorized YAMAHA Retailer or
the appointed service represelllalive.

IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization. certification or
recoglliuon of arty applicable technical capabilities. or establish a pi-incipleeagent relationship of any form

The data provided is believed to be accurate and applicable to the iinitis) indicated on the cover. The research. engineering and service

departntents Of YAMAHA are continually striving to nnproye YAMAHA products Modifications are. Iherefore, inevitable and

specifications are subyect to change \vIIIlmII notice or obligation to retrofit Should arty discrepancy appear to exist. please contact the
distributors service Division,

WARNING: static discharges can destroy expensive components Discharge any static electricity your body may have
accumulated by grounding yourseltto the ground buss m the unit (heavy gauge blaclt wrres connect to this buss).

IMPORTANT: Tiirn the unit OFF during disassembly and part replacement, Reclleck all work betore you apply power to the utiit.

I CONTENTS

TO SERVICE PERSONNEL ........................................ 2-4 DISPLAY DATA

PREVENTION OF ELECTROSTATIC DISCHARGE ...... 5 IC DATA ...........

SYSTEM COMPOSITION / 9X;L\I§5§ PIN CONNECTION DIAGRAMS .
FRONT PANEL .. BLOCK DIAGRAM ................

REAR PANELS
SPECIFICATIONS/ eerie
INTERNAL VIEW ..................
DISASSEMBLY PROCEDURES / fihflillLE
TEST MODE/7'1 I~T:-- F .......................
UPDATING FIRMWARE/

77-A'7170gi5b3; ..................................... 16-20

' :wv- tx::armzc137-7gafimfiimfiififia I/TwiTe
This Service Manual uses recycled paper.

Copyright © 2005 YAMAHA CORPORATION All rights reserved.
Thls manual is copyrighted by YAMAHA and may not be copied Or
redistributed either In print or electronically Without permission,

PRINTED CIRCUIT BOARDS
SCHEMATIC DIAGRAMS
REPLACEMENT PARTS LIST .
REMOTE CONTROL ..................................................... 54

YAMAHA

YAMAHA CORPORATION

P.O.Box 1, Hamamatsu, Japan
animate '08.]1

Page 2

CD-1330

N

CD-1330

I TO SERVICE PERSONNEL

.Critical Components lntormatlon

Components having special characteristics are marked A and
must be replaced with parts having specifications equal to those
originally installed.

2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.

0 Meter impedance should be equivalent to 1500 ohms shunted
by 0.15 IIF.

AC LEAKAGE
WALL EQUIPMENT TESTER OR
OUTLET UNDER TEST EQUIVALENT
INSULATING
TABLE

- Leakage current must not exceed 0.5mA.
0 Be sure to test for leakage with the AC plug in both polariA
ties.

WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive

harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON

WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or

expose eyes to solder/flux vapor!

It you come in contact with solder or components located inside the enclosure of this product, wash your hands before

handling food.

About lead free solder / fifial \DfiIZ'DLVZ

All of the P.C.B.s installed in this unit and solder joints are
soldered using the lead free solder.

Among some types of lead free solder currently available,
it is recommended to use one of the following types for
the repair work.

0 Sn + Ag + Cu (tin + silver + copper)

0 Sn + Cu (tin + copper)

0 Sn + Zn + Bi (tin + ZlnC + bismuth)

Caution:
As the melting point temperature of the lead tree solder
is about 30°C to 40°C (50°F to 70°F) higher than that of
the lead solder, be sure to use a soldering iron suitable
to each solder.

$%K%§$h?vpiNTQEWfiiUflyfifiwfi
gaeealzlmaa/ \y/JTv \ysflnlfehfmim
fifiul \Vfililiv < Goaltéifibfi U $3731 Ilgflfill
liFEEUDo'C 5 may \\/ @UJEIfiEIEiE; L332

- Sn+Ag+Cu (3% + E + 31%)

- Sn+Cu (fiJrflEl)

- Sn+Zn+Bi ($55 + fifiu + 61770
if"
fifiétlv/Jmflfi ElifiemaAU/valztto 30~
40 DCTEEIE] < Ev-Cvifia)? %h%h®/\/§ ILIIJ 3
tnyfiéfaéfifl