Xtant 4180 x owners manual

Page 1

MAXI FUSE 60 AMP REMOTE GROUND + 12 V GREEN LED NOISE GATEYELLOW LED LOW IMPEDANCE LEFT CH . RIGHT CH . FRONT GAINREAR GAIN ORANGE LED THERMAL PROTECTRED LED POWER ON SPEAKER OUTPUTS LEFT LEFT LEFT LEFTLEFT LEFT RIGHT RIGHTRIGHT SUMMED OUTPUT JUMPER SUMMED NORMAL FRONT REAR RIGHT INPUTSFRONT FRONT REAR REAR REAR REAR FRONT LINE OUTPUTS RCA INPUT SELECTOR LINE OUT – SUMMED OUTPUT :THIS PROVIDES A CONSTANT OUTPUT SIGNAL - NOT AFFECTED BY FADER CONTROLLED INPUT SIGNALS . BOTH LEFT RCA OUTPUTS ARE COMMON AND BOTH RIGHT RCA OUTPUTS ARE COMMON . WHEN SUMMING , ANY LEFT AND RIGHT RCA OUTPUT COMBINATION MAY BE USED. FRONT INPUT SENSITIVITY REAR INPUT SENSITIVITY +20 +10 0 –10 –20 +20 2 CHANNEL JUMPER POSITION +10 0 –10 –20 + – +POSITIVE +POSITIVE – –NEGATIVE –NEGATIVE ++ – –+ FRONT AMPAMP RCA RCA REAR FAN CROSSOVERMODE JUMPERS : CROSSOVER SIP SOCKETS CROSSOVER SIP SOCKETS DEFEATIN 2 HP 3 LP 1 BYP 2 HP 3 LP 1 BYP REMOTESWITCHED 12 VOLTS 16 GAUGE MINIMUM NOTE : ADD 60 AMP FUSE AT POSITIVE TER - MINAL OF THE BATTERY . NOISE GATE SWITCH :UP POSITION = ON ; DOWN POSITION = OFFNOISE GATE THRESHOLD ADJUST :TURN CLOCKWISE TO INCREASE SENSITIVITY (GATE WILL OPEN WITH LESS INPUT SIGNAL ) GROUND – 8 GAUGEMINIMUM POWER – 8 GAUGEMINIMUM BRIDGED OUTPUT CONNECTIONBRIDGED OUTPUT CONNECTION ACCESSORY MODULE PORTS BALANCED LINE MODULE PORTS INPUT SENSITIVITY :TO ADJUST INPUT GAIN , MOVE JUMPER (IF NEEDED ) – AND INSTALL IT IN THE LOCATION WHICH MATCHES YOUR INPUT SIGNAL LEVEL . REFER TO THE ILLUSTRATION BELOW FOR PROPER JUMPER LOCATION / LEVEL SETTING . NOTE : –20 dB = 10V – 17V IS ONLY TO BE USED WITH BALANCED INPUT FROM A BALANCED SOURCE . –10 dB = 3V – 8V 0 dB = 1V – 3V +10 dB = 300mV–1V +20 dB = 100 – 300mV THIS SYMBOL INDICATES THE LOCATION OF THE FOUR (4) MOUNTING SLEEVES . CROSSOVERFREQUENCY SELECTION : TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND /OR LOW PASS FILTERS , REMOVE AND REPLACE THE90 H Z FREQUENCY MODULE (SIP ) INSTALLED ON THE CIRCUIT BOARD NEXT TO THE CROSSOVER MODE JUMPERS . NOTE THAT THE IDENTITY OF THE HIGH & LOW PASS SOCKETS ARE NOT MARKED ON THE BOARD . REFER TO THIS DRAWING FOR LOCA - TION & THE CHART ON THE BACK FOR THE INCLUDED SELECTION OF SIP / FRE - QUENCY VALUES . RCA OUTPUTS : 3 – L OW PASS 2 – H IGH PASS 1 – BYP ASS AMPLIFIER : 3 – L OW PASS 2 – H IGH PASS 1 – BYP ASS HIGH PASS HIGH PASS XTANT TECHNOLOGIES 7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 PHONE: 602.431.8686 FAX 602.431.8600 LOW PASS LOW PASS INSTALLERS REFERENCE .............. XTANT 4180X.............. Caution: SHARP EDGES be careful when handling top and bottom metal. factory adjustment only do not attempt to adjust these controls REMOVE JUMPERS (2) PRIOR TO INSTALLATION OF ACCESSORY MODULES.JUMPERS MUST BE IN -PLACE WHEN MODULES ARE NOT INSTALLED . SPEAKER WIRE – 14 GAUGE MINIMUM RIGHT –20 dB = 10V – 17V 2 HP 3 LP 1 BYP 2 HP 3 LP 1 BYP FRONTRIGHT 4 CHANNEL JUMPER POSITION