Sony xr 5500 service manual

This is the 24 pages manual for sony xr 5500 service manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.

Page: 1 / 24
sony xr 5500 service manual

Extracted text from sony xr 5500 service manual (Ocr-read)


Page 1

SERVICE MANUAL

US Model
Canadian Model

Model Name Using Similar Mechanism XR4147/4157

Tape Transport Mechanism Type MG-86VJ-32

SPECIFICATIONS

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION 11 watts
per channel minimum continuous average power into 4 ohms, both
channels driven, from 30-20,000Hz with no more than 1% total

harmonic distortion.

OTHER SPECIFICATION

Power nrnplltler section
Outpus Speaker outputs (sure seal
connectors)
Preamp outputs (phone jams)
Speaker impedance
3.2 - 5 ohms
Maximum power output
25W x 2 (at 4 ohms)
6W x 4 (at 4 ohms)
Measured at 14.4V

Cassette player section

Tape track rack 2-channel stereo
Frequency response
40 -15.000 H1

Signal-tonoise ratio
With type II, N asserts Sada

(Dolby NFI on)
With type I cassette 55.15 (Dolby
NFI off)

Dolby 3 NH elfect
8615

Wow and flutter 0.15% (WRMS)

mner section

System Superheterodyne tuner
Computerized mam-locked
synthesizer system

Antenna terminal FM/AM external antenna connector
FMIAM power amenna relay control
lead

FM tuner section
Tuning range 878 -1a79 MHz
Intermediate frequent.)I

10.7 MHZ

Usable sensitivity 125dBl (75 ohms)
Selectivity TDdB at 400kHz
SignaHovncise ratio

65:15 (stereo). cede (mono)
Harmonic distortion at 1kHz

0.9% (stereo)

05% (mono)
Separation 35dB at 1kHz
Frequenw response

30 - 15.000 Hz

Capture ratio 20 dB

AM tuner section
Tuning range 530 - 1,710 kHz
Intermediate frequency

450 kHz
Sensitivity 34W

General
'bne controls Bass :BdB at IOOHz
Treble .1865 at film:

Loudness + 6dB at 100 Hz
4- 6 dB at leHz
Output lead Power antenna relay control lead

- Continued on page 2 -

FM /AM CASSETTE CAR STEREII

SONY;

Page 2

XR-5500 |

Power requirements
12V Dc car battery (negative
ground) Section Ttl P
Dimensions Approx. 173 x so x 160 mm (wlhld) - fi fl
(7'!a x 2 x 63/o Inches)

TABLE OF CONTENTS

not incl. projecting pans and Specifications ..................................................................... 1
oontmls
Mounting dimensions
mm. 152 x 53 x145mm(wlhld) 1. GENERAL
(7I. x 2'], x 53/. inches) _ - ~ .........................
m incl. projecting pans and 1 1. Location and Function of Controls 3
controls 1-2. Installation -~4

Weight Approx. 13kg (2 lb 14 oz) 1.3_ Connections--
Accessories eupplled
Mounting hardware (I set)

..5

2. ADJUSTMENTS .......................................................... 6
Design and specifications subject to change without
notice.
3. DIAGRAMS
3-1. Semiconductors Lead Layout~ ~11
3-2. Printed Wiring Boards-- 11
33. Schematic Diagram ------- ~- 15
4. EXPLODED VlEWSm ------ 21
5_ ELECTRICAL PATRS LIST ...................................... 27
Flexible Circuit Board Repairing MODEL IDENTIFICATION

0 Keep the temperature of the soldering iron around

270°C during repairing. S ONY. MODEL NO. X R'5 5 o 0

0 Do not touch the soldering iron on the same conduc-

tor of the circuit board (within 3 times). F M/AM CASSETTE CAR STEREO
0 Be careful not to apply force on the conductor when F R EO U E N CY RA N G E Z

soldering or unsoldering. FM 87 9 1 07 9 M HZ

Notes on chip component replacement AM 5 30"1 71 0 KHZ

0 Never reuse a disconnected chip component. DC : 12V: NEGATIVE GROUND
0 Notice that the minus side of a tantalum capacitor

may be damaged by heat. SERIAL N0.

MADE IN. W
MALAYSIA

Singapore