Sony tc fx 510 r service manual

Page 1

TC-FXSIO

US Model
Canadian Model
AE P Model

UK Model
E Model

SERVICE MANUAL

Doby and the double-D symbol are the trade marks of
Dolby Ldaoretories Licensing Corporation. Noise reduction
system manufactured under license from Dolby Laboratories

Licensing Corporation.

Recording system 4-track 2-channel stereo
Fast-forward and rewind time

SPECIFICATIONS

Approx. 90 sec. (with C-60 cassette)

Bias frequency 105 kHz
Signal-to-noise ratio (NAB. at peak level)

DolbyiNFl button

Frequency response

CTYPE ON

Tape Transport
Mechanism Type

DOLBY NR OFF

0 With TYPE IV cassette (Sony METALLIC)
20 - 18,000 Hz
30 - 17,000 Hz (:3 dB)
30 13,000 Hz (:3 d8. 0 VU recording)

- With TYPE ll cassette (Sony UCX)

TCM-ISORI

Cassette OFF , ,BLTYPE ON ,, __ , _ 20 - 18 000 Hz

TYPE lV (Sony METALLlC) 58 dB 65 dB 71 dB 30 - 17,000 Hz (:3 dB)

L L.. 4- .g_ - -- --- . With TYPE I cassette (Sony BHF)
TYPE ll (Sony UCX) 56 dB 63 dB 69 dB 20 - 16 om Hz

Type I (Sony 3gp) i 54 d8 51 d8 67 (18 I Wow and flutter 0.045% WRMS (NAB)

x, _ ,- a _._- _._ ___ , 10.15% (DIN)

Total harmonic distortion Inputs Microphone inputs (phone jacks)
1.0% (with Sony METALLIC cassettes) Sensitivity 0.25 mV (-70 dB)
For a low-impedance microphone
Line inputs (phono jacks)
Sensitivity 77.5 mv (-20 dB)
SAFETY-RELATED COMPONENT WARNING Input impedance 50 k ohms
COMPONENTS IDENTIFIED ev SHADING ANO MARK OUIDU'S Une OUIWS Iph°n° 130)

A ON THE SCHEMATIC DIAGRAMS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION Au COMPOSANT AYANT RAPPORT
A LA sEcunn'Et

LES COMPOSANTS IDENTIFIES PAR UNE TRAME ET
UNE MAROUE A sun LES DIAGRAMMES SCHE-
MATIOUES ET LA LlSTE OES PIECES SONTCRITIOUES
Poun LA sEcunrrE OE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS OUE PAR DES PIECES
SONY DONT LES NUMEROS SONT DONNES OANS CE
MANUEL ou DANS LES SUPPLEMENTS PUBLIES PAR
SONY.

MICROFILM

Output level 0.44 V (-5 dB) at load

impedance 50 k ohms

Load impedance over 10 k ohms
Headphone output (stereo phone jack)

Output level -28 dB at a load impedance

of 8 ohms

0dB-0.775v -Continued on page2 _

3mm cnssmr DECK
SONY;

Page 2

Gan-Ii

Power requirements US, Canadian Model:
120 V ac, 60 Hz
AEP, G-AEP Model:
220 V ac, 50/60 Hz
(240 V ac adjustable by authorized
Sony personnel)
UK Modal:
240 V ac, 50/60 Hz
(220 V ac adjustable by authorized
Sony personnel)

E Modal:

110,120, 2200r240Vacadlustabla,

50/60 Hz
Power consumption 24 watts
Dimensions

(17 X 4V. X 10% inch)
including projecting parts and controls

Weight Approx. 4.7 kg (10 lbs 6 02)

MODEL lDENTlFiCATION
- Specification Label -

TAPECORDER

SERIAL NO.
MADE IN JAPAN

US, Canadian model: AC: 120 V 60 Hz 24 W
AEP, G-AEP model: AC: 220 V ~50/60 Hz 24W

SONY» MODEL N0. rc-Fxs1oa

Approx. 430 x 105 x 275 mm luv/hid)

UK modal: AC: 240V ~50/60 Hz 24 W
E modal: AC: 110, 120, 220, 240 V ~50/60 Hz 24 W
- Power Cord -

E2 Modal

Prallal-biada plug

1-551-472-00

E3 Modal
Euro-pit.
1-555-734-00

SAFETY CHECK-OUT (US Modal)

After correcting the original service problem,
perform the following safety check before releasing
the set to the customer:

Check the antenna terminals, metal trim, metallized
knobs, screws, and all other exposed metal parts for
AC leakage. Check leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to
earth ground and from all exposed metal parts to any
exposed metal part having a return to chassis, must
not exceed 0.5 mA (500 microampereS). Leakage
current can be measured by any one of three
methods.

I. A commercial leakage tester, such as the
Simpson 229 or RCA WT-S40A. Follow the
manufacturers' instructions to use these instru-
ments.

2. A battery-operated AC milliammeter. The Data
Precision 245 digital multimeter is suitable for
this job.

3. Measuring the voltage drop across a resistor by
means of a VOM or battery-operated AC volt-
meter. The limit indication is 0.75 V, so
analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa
SH-63Trd are examples of a passive VOM that
is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are
suitable. (See Fig. A)

To Exposed Metal
Parts on Set

0

0.15 F J:-_4r.5m _4
Ti *

A C
voltmeter
(0. 75 V)

'1; Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.