Sony str sl 7 owners manual

Page 1

S 0 NY 4-235-542-11(1)
6)

FM Stereo
FM-AM Receiver

Operating Instructions

Owner's Record

The model and serial numbers are located on the rear panel. Record the serial number
in the space provided below. Refer to them whenever you call upon your Sony dealer
regarding this product.

Model No. - Serial No.

STE-8L7

© 2001 Sony Corporation

Page 2

To prevent fire or shock hazard, do not
expose the unit to rain or moisture.

Dont throw a battery, dispose it as
the injurious wastes.

Wm murmmr mm [chvmcsmcK

no My arvovr cnvra m um

This symbol is intended to alert the user to
A the presence of uninsulated dangerous
voltage" within the product's enclosure that

may be of sufficient magnitude to constitute
a risk of electric shock to persons.

This symbol is intended to alert the user to
& the presence of important operating and

maintenance (sen/icing) instructions in the

literature accompanying the appliance.

WARNI G

This equipment has been tested and found to comply

with the Limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,
which can be determined by tuming the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:

~ Reorient or relocate the receiving antenna.

~ Increase the separation between the equipment and
receiver.

4 Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV
technician for help.

CAUTION
You are cautioned that any changes or modifications

not expressly approved in this manual could void
your authority to operate this equipment.

Note to CATV system installer

This reminder is provided to call the CATV system
installers attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.

This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories.
Dolby", Pro Logic and the double-D symbol are
trademarks of Dolby Laboratories.
** DTS and DTS Digital Surround" are registered
trademarks of Digital Theater Systems, Inc.
Tip
The instructions in this manual describe the controls
on the receiver. You can also use the controls on the
supplied remote if they have the same or similar
names as those on the receiver. For details on the use
of your remote, see pages 33-36.

Demonstration Mode
The demonstration will activate the first time you
turn on the power. When the demonstration starts,
the following message appears in the display
twice:
NOW DEMONSTRATION MODE IF YOU
FINISH DEMONSTRATION PLEASE PRESS
POWER KEY WHILE THIS MESSAGE
APPEARS IN THE DISPLAY THANK YOU

To cancel the demonstration

Press |/(') to turn the receiver off during the
previous message. The next time you turn the
receiver on. the demonstration will not appear.

To view the demonstration

Hold down SET UP and press l/L) to turn on the
power.

Notes

- Running the demonstration will clear the

receivers memory. For details on what will be

cleared, see Clearing the receivers memory"

on page 13.

There will be no sound when the demonstration

mode is activated.

- You cannot cancel demonstration if you did not
press I/Q) while the above message is being
displayed. To cancel demonstration after the
above message appears, press |/(') twice to
activate the demonstration again. Then, press
I/Q) while the above message is being
displayed.