Sony mds ja 30 es owners manual

This is the 85 pages manual for sony mds ja 30 es owners manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.

Page: 1 / 85
sony mds ja 30 es owners manual

Extracted text from sony mds ja 30 es owners manual (Ocr-read)


Page 2

ZEN

To prevent fire or shock
hazard. do not expose the unit
to rain or moisture.

To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.

The laser component in this product
is capable of emitting radiation
exceeding the limit for Class 1.

CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE

KLASS I LASERAPPARAT

This appliance is classified as a CLASS 1
LASER product. The CLASS 1 LASER
PRODUCT MARKING is located on the
rear exterior.

The following caution label is located
inside of the unit.

ewe-W
VW , azv-zwmeaemw
mm eremr.:erm* ~
AWAHSEL I mflzmlflnéfiwztaififl Ann

@

For the customers in the
United States

AEA

A

This symbol is intended to alert the user

to the presence of uninsulated
"dangerous voltage within the
products enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.

&

This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing)
instructions in the literature
accompanying, the appliance.

CAUTION
The use of optical instruments with this
product will Increase eye lid/uni.

Owner's Record

The model and serial numbers are
located on the rear of the unit.
Record these numbers in the spaces
provided below. Refer to them
whenever you call upon your Sony
dealer regarding this product.

Model No. MDSaJAEOES
Serial No.

INFORMATION

This equipment has been tested and

found to comply with the limits for a

Class B digital device, pursuant to Part

15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if

not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:

, Reorient or relocate the receiving
antenna. V i

~ Increase the separation between the
equipment and receiver.

- Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.

- Consult the dealer or an experienced
radio/TV technician for help.

CAUTION

You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority
to operate this equipment.

IN NO EVENT SHALL SELLER BE
LIABLE FOR ANY DIRECT,
INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR
EXIENS S RESULTING FROM
ANY D CTlVE PRODUCT OR
THE USE OF ANY PRODUCT.

-
Precautions

0n safety

Should any solid object or liquid fall
into the cabinet, unplug the deck and
have it checked by qualified personnel
before operating it any further.

0n power sources
I Before operating the deck, check that
the operating voltage of the deck is
identical with your local power
supply. The operating voltage is
indicated on the nameplate at the rear
of the deck.
If you are not going to use the deck
for a long time, be sure to disconnect
the deck from the wall outlet. To
disconnect the AC power cord, grasp
the plug itself; never pull the cord.
The mains switch is located on the
rear exterior (only on European
model).
- AC power cord must be changed only
at the qualified service shop.

On placement

Do not install the appliance in a
confined space, such as a bookcase or
built-in cabinet because the mains
power switch (MAIN POWER) is
located on the rear exterior (only on
European model).

On operation

If the deck is brought directly from a
cold to a warm location, or is placed in a
very damp room, moisture may
condense on the lenses inside the deck.
Should this occur, the deck may not
operate properly. In this case, remove
the MD and leave the deck turned on
for about an hour until the moisture
evaporates.