Sony cfd s 20 cp service manual
This is the 64 pages manual for sony cfd s 20 cp service manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from sony cfd s 20 cp service manual (Ocr-read)
Page 1
CFD-SZDCP
SERVICE MANUAL us Model
Canadian Model
Taiwan Model
Korean Model
Ver 1.4 2004. 09
Model Name Using Similar Mechanism CFD-S400l8500
Saigon CD Mechanism Type KSM-213RDP
Optical Pick-up Name KSS-213R
TC Model Name Using Similar Mechanism CFD-S400l8500
Section Tape Transport Mechanism Type MF-SZOO
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS Radio section
POWER OUTPUT AND TOTAL Frequentl' range
HARMONIC DISTORTION FM 875 * 103 MHZ
AM: 530 , L710 kHz (USi CND)
Wflh 3.2-ohm loads, both channels drlven from AM: 531 , 1.611 kHz (KR. TW)
150 - 6,300 Hz; rated 1.8 W per channel-
_ _ _ Antennas
mlnlmum RMS power, Wlth no more than 10% FM: Telescopic manna
total harmonic distortion in AC operation. AM: Buillrln ferrite bar antenna
Cassette-corder section
Recording system
Astrack 2 channel stereo
Fast Winding time
Approx. 120 sec. with Sony cassette C760
Frequency response
TYPE 1 (normal): 80 , 10,000 Hz
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material; GaAlAs
Wave length: 780 nm
Emission duration; Continuous
Laser output: Less than 44.5 pw - Continued on next page -
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pickrup block with 7 mm apemlre.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 , 20,000 Hz +1/72 dB
Wow and flutter
Below measurable limit
CD RADIO CASSETTE-CORDER
9-873-978-05 Sony Corporation S O N Y
2004I04-1 Personal Audio Company
© 2004. 09 Published by Sony Engineering Corporation ®
Page 2
CFD-SZOCP
Ver 1.3
General
Speaker
Full range: 10cm (4ln.)dia..
3.2 ohnls. cone type (2)
Outputs
Headphones jack (stereo lnlnijack)
For 16 . 68 ohms impedance headphones
Power output
2.3 W + 2.3 W (at 3.2 chills. 10%
harmonic distortion)
Power requirements
For CD radio cassettercorder:
US. CND. TW model:
120 V AC, 60 HZ
KR model:
220 V AC, 60 HZ
9 V DC, 6 Size D (R20) batteries
For remote control:
3 V DC, 2 Size AA (R6) batteries
Battery life
For CD radio cassettercorder:
FM recording
Sony mop: approx. 13 5 h
Sony alkaline LR20: approx 20 h
Tape playback
Sony Rzor: approx. 7.5 h
Sony alkaline 1.1220: approx 15 h
CD playback
Sony RZOP: approx. 2.5 h
Sony alkaline LR20: approx. 7 h
Dimensions
Approx. 386 X 166 X 252 mm (w/h/d)
<15 m X 5 5/8 X lOinclles)(me1. projecting pans)
Mass
Approx 3.3 kg (7 lb. 4 oz.) (incl. batteries)
Supplied accessories
AC power cord (1)
Remote control (RMTVCSZOCPA) (1)
Design and specifications are subject to change Without
notice.
- Abbreviation
CND : Canadian nlodel
KR : Korean model
TW : Tarwan model
CAUTION
Use of controls or adjustments or perfomlance of proce
dures other than those specified herein may result in haz-
ardous radiation exposure.
Flexible Circuit Board Repairing
0 Keep the temperature of the soldering iron around 270°C during
repairing.
- Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
0 Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on Chip Component Replacement
' Never reuse a disconnected chip component.
0 Notice that the minus side ofa tantalum capacitor may be dam»
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick»
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
SAFETY-RELATED COMPONENT WARNING
COMPONENTS IDENTIFIED BY MARK A OR DOTTED LINE
WITH MARK A ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
A LA SECURITE!!
LES COMPOSANTS IDENTIFIES PAR UNE MARQUE A SUR LES
DIAGRAMMES SCHEMATIQUES ET LA LISTE DES PIECES SONT
CRITIQUES POUR LA SECURITE DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIECES SONY
DONT LES NUMEROS SONT DONNES DANS CE MANUEL 0U
DANS LES SUPPLEMENTS PUBLIES PAR SONY.