Sony cfd g 35 owners manual
This is the 2 pages manual for sony cfd g 35 owners manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from sony cfd g 35 owners manual (Ocr-read)
Page 1
Listening to the radio 1 Press POWER to turn on the player. 2 Press BAND-AUTO PRESET until the band you want appears in the display. Each time you press the button, the indication changes as follows: FM t AM. 3 Hold down TUNE + or – until the frequency digits begin to change in the display. The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step. TipIf the FM broadcast is noisy, press MODE until "Mono" appears in the display and the radio will play in monaural. Presetting radio stations You can store radio stations into the players memory. You can preset up to 30 radio stations, 20 for FM and 10 for AM in any order. 1 Press POWER to turn on the player. 2 Press BAND-AUTO PRESET to select the band. 3 Hold down BAND-AUTO PRESET for 2 seconds until AUTO flashes in the display. 4 Press DISPLAY-ENTER-MEMORY. The stations are stored in memory from the lower frequencies to the higher ones. If a station cannot be preset automatically You need to preset a station with a weak signal manually. 1Press POWER to turn on the player. 2Press BAND-AUTO PRESET to select the band. 3Tune in a station you want. 4Hold down DISPLAY- ENTER-MEMORY for 2 seconds until the preset number flashes in the display. 5Press PRESET + or – until the preset number you want for the station flashes in the display. 6Press DISPLAY-ENTER-MEMORY. The new station replaces the old one. On the remote1Press BAND until the band you want appears in the display. 2Tune in a station you want. 3Hold down the number buttons that you want to preset the new station on for about 2 seconds. To select the preset number over 10, press >10 first, then the corresponding number buttons. You need to hold down the last number button to enter for about 2 seconds. (Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.) Playing preset radio stations 1 Press POWER to turn on the player. 2 Press BAND-AUTO PRESET to select the band. 3 Press PRESET + or – tune in the stored station. On the remote 1Press BAND. 2Press the number buttons to tune in the stored station. To tune in a preset station over 10, press >10 first, then corresponding number buttons. (Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.) Playing a tape 1 Press POWER to turn on the player. 2 Press xZ to open the tape compartment and insert a recorded tape. Close the compartment. Use TYPE I (normal) tape only. 3 Press N. Tostop playback fast-forward or rewind the tape pause playback eject the cassette To turn on/off the powerPress POWER. To adjust the volumePress VOLUME +, – (VOL +, – on the remote). To listen through headphonesConnect the headphones to the i (headphones) jack. Selecting the audio emphasis (SOUND/POWER DRIVE WOOFER) You can adjust the audio emphasis of the sound you are listening to. Selecting the sound characteristicPress SOUND repeatedly to select the audio emphasis you want. Choose To get powerful, clean sounds, emphasizing low and high range audio light, bright sounds emphasizing high and middle range audio percussive sounds, emphasizing bass audio the presence of vocals, stressing middle range audio the whole dynamic range for music such as classical music Reinforcing the bass sound Press POWER DRIVE WOOFER (WOOFER on the remote). appears in the display. When POWER DRIVE WOOFER function works, the button lights up. To return to normal sound, press the button until the indication disappears from the display . Notes - While the sleeping timer is on, the POWER DRIVE WOOFER button does not light, even if the WOOFER function works. - When using the headphones, the WOOFER function does not work. Falling asleep to music 1 Play the music source you want. 2 Press SLEEP. 3 Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: 60 t 90 t 120 t OFF t 10 t 20 t 30. To cancel the sleep function Press POWER to turn off the power. Note When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. Remote Control Location of controls FUNCTION BANDPOWER VOL +*, – x .,> Then do this Press . or > to select the track that you want to repeat, then press u. Press u. Press u. Press u. Press . or > then press DISPLAY-ENTER- MEMORY for the tracks you want to program in the order you want up to 20 tracks (see fig. E). Then press u. Press . or > then press DISPLAY-ENTER- MEMORY for the tracks you want to program in the order you want up to 20 tracks. Then Press u. Z PUSH OPEN/CLOSE VOLUME –, +* TUNE –, +DISPLAY ENTER MEMORY MODE iNumber buttons x u* POWER SLEEP OPR/BATT Loading a CD With the labeled side up Inserting a cassette With the side you want to play facing upward BAND AUTO PRESET SOUND Display Remote sensor Total track number Programmed track Playing order DE Total playing time Display Press x u (X on the remote) Press the button again to resume play after pause. > . Z PUSH OPEN/CLOSE > (forward) or . (backward) while playing until you find the point > (forward) or . (backward) in pause until you find the point a number button of the track on the remote *The button has a tactile dot. POWER DRIVE WOOFER., > PRESET –, +N X SLEEP MODE TUNE+, – WOOFER SOUND Recording 1 Press POWER to turn on the player. 2 Press xZ to open the tape compartment and insert a blank tape. Use TYPE I (normal) tape only. 3 Select the program source you want to record. To record from the CD player Press x and load a CD (See Playing a CD). To record from the radio Press BAND-AUTO PRESET and tune in the station you want (See Listening to the radio). 4 Press z to start recording. (N is depressed automatically.) To Pressstop recordingxZ pause recordingX Press the button again to resume recording. Tips - Adjusting the volume or the audio emphasis will not affect the recording level. - For the best results, use the AC power as a power source for recording. - To erase a recording, proceed as follows: 1 Insert a tape with the recording you want to erase. 2 Press X. 3 Press N. 4 Press z. 5 Press X. Press xZ M or m X Press the button again to resume play after pause. xZ Playing a CD 1 Press POWER to turn on the player. 2 Load a CD in the CD compartment. 3 Press Z PUSH OPEN/CLOSE to close the CD compartment. 4 Press u (N on the remote). The player plays all the tracks once. Tostop playback pause playback go to the next track go back to the previous track remove the CD locate a point while listening to the sound locate a point while observing the display locate a specific track directly* * You cannot locate a specific track if "SHUF" or "PGM" is lit in the display. Turn off the indication by pressing x. TipTo locate a track numbered over 10, press >10 first, then the corresponding number buttons on the remote. Example:To play track number 23, press >10 first, then 2 and 3. Using the display To check the total track number and playing timePress DISPLAY-ENTER-MEMORY in stop mode (see fig. D). To check the remaining timePress DISPLAY-ENTER-MEMORY repeatedly while playing a CD. The display changes as follows: tthe current track number and playing time r the current track number and the remaining time on the current track* r the number of tracks left and remaining time on the CD * For a track whose number is more than 20, the remaining time appears as - -:- - in the display. Selecting the play mode Press MODE until REP 1 REP ALL SHUF SHUF REP PGM PGM REP appears in the display. Then proceed as follows: To Select repeat a single track REP 1 repeat all tracks REP ALL shuffle play SHUF repeat tracks SHUF REP in random order program play PGM repeat programmed tracks PGM REP On the remoteWhen youve selected PGM or PGM REP, press the number buttons for the track you want up to 20 tracks, then press N. To cancel selected play modePress MODE until the selected mode disappears from the display. To check the programmed track and playing order in the displayTo check the order of tracks before play, press DISPLAY-ENTER-MEMORY. Every time you press the button, the track number appears in the programmed order. To change the current programPress x once if the CD is stopped and twice if the CD is playing. The current program will be erased. Then create a new program following the programming procedure. Tips - You can play the same program again, since the program is saved until you open the CD compartment. - You can record your own program. After youve created the program, insert a blank tape and press z to start recording.