Sony cfd e 10 service manual

This is the 34 pages manual for sony cfd e 10 service manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.

Page: 1 / 34
sony cfd e 10 service manual

Extracted text from sony cfd e 10 service manual (Ocr-read)


Page 1

2 CFD-E10 Flexible Circuit Board Repairing -Keep the temperature of the soldering iron around 270 ˚C dur- ing repairing. -Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). -Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement -Never reuse a disconnected chip component. -Notice that the minus side of a tantalum capacitor may be dam- aged by heat. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. On AC power adaptor -Use only the AC power adaptor supplied or recommended in Accessories (supplied/ optional). Do not use any other AC power adaptor. It may cause a malfunction. Polarity of the plug TABLE OF CONTENTS SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT 1. GENERAL ·········································································· 3 2. DISASSEMBLY ································································ 4 2-1. Cabinet Front Assy, Cabinet Rear Assy ························· 4 2-2. TU Board, AUDIO Board ·············································· 5 2-3. LCD Board ···································································· 5 2-4. CD Lid Assy ·································································· 6 2-5. CD Holder ····································································· 6 2-6. CD Board ······································································· 7 2-7. Optical Pick-up (KSM-900AMA) ································· 7 2-8. Optical Pick-up (KSS-900A) ········································· 8 3. ELECTRICAL ADJUSTMENTS ································· 9 4. DIAGRAMS ······································································ 11 4-1. IC Pin Function Description ········································ 12 4-2. Block Diagram ···························································· 13 4-3. Printed Wiring Board – TUNER Section – ················ 14 4-4. Schematic Diagram – TUNER Section – ··················· 15 4-5. Printed Wiring Board – CD Section – ························ 16 4-6. Schematic Diagram – CD Section (1/2) – ·················· 17 4-7. Schematic Diagram – CD Section (2/2) – ·················· 18 4-8. Printed Wiring Board – AUDIO Section – ················· 19 4-9. Schematic Diagram – AUDIO Section – ···················· 20 5. EXPLODED VIEWS ······················································ 23 5-1. Cabinet Front/Rear Section ········································· 23 5-2. Cabinet Center Section ················································ 24 5-3. CD Holder Section ······················································ 25 5-4. Optical Pick-up Section (KSM-900AMA) ·················· 26 6. ELECTRICAL PARTS LIST ······································· 27

Page 2

3 CFD-E10 SECTION 1 GENERAL This section is extracted from instruction manual. MEGA BASS POWER OPR/BATTFUNCTION VOL* PLAY MODE DC IN 6VTUNING DisplayPUSH CLOSE ** *There is a tactile dot beside VOL to show the direction to turn up the volume. ** The u button has a tactile dot. i (headphones) About CD-Rs/CD-RWs This CD player can play CD-Rs/CD-RWs recorded in the CD-DA format*, but playback capability may vary depending on the quality of the disc and the condition of the recording device. *CD-DA is the abbreviation for Compact Disc Digital Audio. It is a recording standard used for Audio CDs.