Sony cdx s 2200 service manual

Page 1

CDX-SZZIIII

SERVICE MANUAL AEP Model

Ver 1.0 2004. 05 UK Model

' 9 m and CD mm have n jsmms- Model Name Using Similar Mechanism CDX-R3300
CD Drive Mechanism Type MG-611MA-186I/Q
Optical Pick-up Name KSSiOOOE

SPECIFICATIONS

CD player section
signal-to-noise ratio 120 dB Power amplifier section
Frequency response 10 , 20.000 Hz Outputs Speaker outputs
Wow and flutter Below measurable limit (sure seal connectors)
Speaker impedance 4 , 8 ohms
Tun" section Maximum power output 50 W x 4 (at 4 ohms)
FM
Timing range 87.5 v [08.0 MHz General
Aerial terminal External aerial oonnector Outputs Audio outputs terminal
Intermediate fiequeney 10.7 MHz/450 kHz (rear)
Usable sensitivity 9 dBf Power aerial relay control terminal
Selectivity 75 dB at 400 kHz Power amplifier control terminal
Signal.to-noise ratio 67 dB (stereo), Inputs Telephone ATI control terminal
69 dB (mono) Remote controller input terminal
Harmonic distortion at 1 kHz Aerial input terminal
0.5% (stereo), Tone controls Low: :10 dB at 60 Hz (XPLOD)
0.3% (mono) Mid 10 dB at 1 kHz ()flLOD)
Separation 35 dB at 1 kHz High: :10 dB at 10 kHz (XPLOD)
Frequency response 30 - 15,000 Hz
MWILw - Continued on next page -
Tuning range MW: 531 - 1,602 kHz
LW: 153 - 279 kHz
Aerial terminal External aerial eonnecter
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity MW: 30 llV
LW: 40 V

FM/MW/LW COMPACT DISC PLAYER
9-877-830-01 Sony Corporation S O N Y
2004E04-1 e Vehicle Company
© 2004. 05 Published by Sony Engineering Corporation ®

Page 2

CDX-SZZOO

Power requirements 12 V DC car battery
(negative ground)

Dimensions Approx, 173 x so x 176 mm
(w/h/d)

Mounting dimensions Approx. 182 x 53 x 161 mm
(W/IJ/d)

Mass Approx. 1.2 kg

Supplied accessories Parts for installation and connections (1 set)

me panel case (1)

Design andspecgfica/iam are sub/'26! to change without
notice

SERVICE NOTES

CAUTION

Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.

This compact disc player is classified as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.

This label is located on the bottom of the chassis.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT

The laser diode in the optical pick-up block may sufier electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.

The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.

Notes on Chlp Component Replacement

' Never reuse a disconnected chip component.

' Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

SAFETY-RELATED COMPONENT WARNINGII

COMPONENTS IDENTIFIED BY MARK A OR DOTTED LINE
WITH MARK A ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.

2

Ifthe optical pick-up block is defective, please replace the whole
optical pick-up block.

Never turn the semi-fixed resistor located at the side of optical
pick~up block.

optical pick-up

semi-fixed resistor

TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:

CD-R test disc TCD-ROSZLMI (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J -2502-063 -2)