Sony cdx c 710 service manual

This is the 56 pages manual for sony cdx c 710 service manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.

Page: 1 / 56
sony cdx c 710 service manual

Extracted text from sony cdx c 710 service manual (Ocr-read)


Page 1

CDX-C710

SERVICE MANUAL

US Model

Model Name Using Similar Mechanism NEW
CD Drive Mechanism Type MG-333E-121
Optical Pick-Up Name KSS-520A
SPECIFICATIONS
CD player section Power amplifier section
System Compact disc digital audio Outputs Speaker outputs
system (sure seal connectors)
Signal-to-noise ratio 90 dB Speaker impedance 4 - 8 ohms
Frequency response 10 - 20/000 Hz Maximum power output 35 w x 4 (at 4 ohms)
Wow and flutter Below measurable limit
Laser Diode Properties General
Material CaAIAs
Wavelength 780 nm Output lead Esrnlfgleixeiznna relay
Emission Duration Continuous . -
Laser output power Less than 446 uW' £23" amplifier control
This output is the value mmsured at a distance of Tone controls Bass :8 dB at 100 Hz
200 mm fram the objective lens surface Im the Optical Treble :8 dB at 10 kHz
Pick-up Block. Power requirements 12 V DC car battery
(negative ground)
Tuner section Dimensions Approx, 188 x58 x 177 mm
FM (7/z><2/tx7inl)
, (w/h/d)
Tums ranse 57-5 - 1°79 MHZ Mounting dimensions Approx 173 x 50 x 154 mm
Antenna terminal External antenna connector (7 1/. x 2 x 6 v, in.)
Intermediate frequency 10.7 MHz (w/h/d)
Usable sensitivity 8 dBf M A ~ 15 k 311.,.
Selectiin'ty 75 dB at 400 kHz 5 4:53: 8 (
Signalto-noise 5° 62 dB (59)! Supplied accessories Rotary remote (1)
55 d3 (mm) Parts for installation and

Harmonic distortion at 1 kHz
0.9 % (stereoL
05 % (mono)

Separation 35 dB at 1 kHz

Frequency response 30 - 15,000 Hz

Capture ratio 2 dB

AM

Tuning range 530 - 1,710 kHz

Antenna terminal External antenna connector
Intermediate frequency 10.71 MHz/450 kHz
Sensitivity 30 )IV

connections (1 set)
Front panel case (1)

Design and specifications are subject to change without
notice,

FM/AM COMPACT DISC PLYER
S 0 NY;

Page 2

TABLE OF CONTENTS

GENERAL

Location of Controls 3
Installation 4
Connections .................................................................... 5
DISASSEMBLY .............................................. 7
TEST MODE. 11

ELECTRICAL ADJUSTMENTS
CD Section 11
Tuner Section 11

DIAGRAMS

Printed Wiring Board - Display Section -
Schematic Diagram - Display Section -
Printed Wiring Board - Main Section -
Schematic Diagram - Main Section
Schematic Diagram

- Mechanism Deck Section -
Printed Wiring Boards

- Mechanism Deck Section - .. . 31
IC Pin Function Description 39
EXPLODED VIEWS ................................................ 45
ELECTRICAL PARTS LIST ............................... 50

SE ifiéfiifiiifitt

SERVICING NOTES

Flexible Circuit Board Repairing

0 Keep the temperature of the soldering iron around 270 C
during repairing.

0 Do not touch the soldering iron on the same conductor of
the circuit board (within 3 times).

0 Be careful not to apply force on the conductor when solder-
ing or unsolderingi

Notes on chip component replacement

0 Never reuse a disconnected chip component.
a Notice that the minus side of a tantalum capacitor may be
damaged by heat.

NOTES ON HANDLING THE OPTICAL
PICK-UP BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer elec<
trostatic breakdown because of the potential difference gen~
erated by the charged electrostatic load, etc. on clothing and
the human body.

During repair. pay attention to electrostatic breakdown and
also use the procedure in the printed matter which is included
in the repair parts.

The flexible board is easily damaged and should be handled
with care.

Laser Diode Properties

0 Material: GaAlAs

. Wavelength: 780 nm

- Emission Duration: continuous

' laser Output Power: less than 44.6 uW*

* This output is the value measured at a distance of 200

mm from the objective lens surface on the Optical Pick-
up Block.

CAUTION

Use of controls or adjustments or performance of pro-
cedures other than those specified herein may result in
hazardous radiation exposure.

SAFETY-RELATED COMPONENT WARNINGII

COMPONENTS IDENTIFIED BY MARK A OR DOTTED
LINE WITH MARK A ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL T0 SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONV.