Sansui HD LCD VD325 Owners Manual
This is the 43 pages manual for Sansui HD LCD VD325 Owners Manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from Sansui HD LCD VD325 Owners Manual (Ocr-read)
Page 1
2 CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS OWNER'S MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. TO PREVENT DIRECT EXPOSURE TO THE LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO THE BEAM.Location of the required Marking The rating sheet and the safety caution are on the rear of the unit. CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OPEN FLAMES AWAY FROM THIS PRODUCT AT TIMES. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. The lamp(s) within this product contain mercury. Disposal should be in compliance with local, state or federal laws. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with the FCC Rules could void the users authority to operate this equipment. Record the model number and serial number. Model number Serial number ENGLISH CLASS 1 LASER PRODUCT
Page 2
3 ENGLISH 15) Apparatus should not be exposed to dripping or splashing, and objects filled with liquids, such as vases, should not be placed on the apparatus. 16) An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. 17) Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock. 18) Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit. 19) If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 20) When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 21) Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition. 22) Keep your fingers clear of the disc slot as it is closing. It may cause injury. ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ANTENNA LEAD IN WIRE GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) GROUND CLAMP ELECTRIC SERVICE EQUIPMENT NEC NATIONAL ELECTRICAL CODE S2898A EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE
Page 18
19 ENGLISH Rating if this data is transmitted. You may set this restriction separately. To use the VChip function, you must register a password. To register a password 1 Press SETUP/TV MENU in the TV mode. The TV menu screen will appear. 2 Press or to select Lock, then press or ENTER. 3 Select and enter your password (4 digits) using Number buttons (09), then press ENTER. [0 9] LockNew Password * * *_ : Select ENTER:Set appears instead of the number. 4 Enter the same password again to confirm, then press ENTER. The password is now registered. NOTE: If you forget the password, contact Customer Service at 1-800-289-0980 for assistance. Your original remote control will be required. To avoid forgetting the password, write it down and keep in a safe place. To set the VChip 1 Press SETUP/TV MENU in the TV mode. The TV menu screen will appear. 2 Press or to select Lock menu, then press or ENTER. 3 Use Number buttons (09) to enter your password, then press ENTER. Then Lock menu will appear. 4 Press or to select V-Chip, then press or to select On . 5 Press or to select V-Chip Set, then press or ENTER. The V-Chip Set Menu appears. 6 Press or to select which rating will be used, then press or ENTER. Each rating below will appear. TV Rating ALL D L S V FV TV Y TV Y7 TV G TV PG TV 14 TV MA ENTER:Set TV Rating : Select You can set the rating using age level and genre. - -Age: TVY : All children TVY7 : 7 years old and above TVG : General audience TVPG : Parental guidance TV14 : 14 years old and above TVMA : 17 years old and above Genre: ALL : All D : Dialogue L : Language S : Sex V : Violence FV : Fantasy Violence Movie Rating G PG PG 13 R NC 17 X ENTER:Set Movie Rating : Select G : All ages PG : Parental guidance PG13 : Parental guidance less than 13 years old R : Under 17 years old parental guidance suggested NC17 : 17 years old and above X : Adult only 7 Press /// to select the desired rating, then press ENTER. 8 Press EXIT/CANCEL to return to the normal screen. V-Chip function is activated now. To use the TV after the TV is protected. When a program is received that is blocked by the V- Chip, press MUTE, then enter your password. The protection will be temporarily overridden. If the TV is turned off or the channel is changed, the V-Chip restriction will be reactivated. NOTE: The V-Chip function is activated only on programs and input sources that include a rating signal. To change the password 1 Press SETUP/TV MENU in the TV mode. The TV menu screen will appear. 2 Press or to select Lock, then press or ENTER. 3 Use Number buttons (09) to enter your password, then press ENTER. The Lock menu will appear. 4 Press or to select Change Password, then press or ENTER. The Change Password screen will appear. 5 Enter a new password using Number buttons (09), then press ENTER. 6 Enter the same password again to confirm, then press ENTER. The password is now registered. -