Pioneer sg 530 service manual
This is the 16 pages manual for pioneer sg 530 service manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from pioneer sg 530 service manual (Ocr-read)
Page 1
1. FRONT PANEL FACILITIES POWER INDICATOR O powen swrrcH Depress this switch to turn power on to the SG-530. Be- cause this switch is connected to the secondary winding of the power transformer, power is still supplied to the pri- mary winding even when the power switch is returned to the STAND-BY ( t] ) position. Always unplug the power cord from the wall socket when the SG-530 is not going to be used for a long time. @ OCTAVE CONTROLS Move these controls above or below the center (zero) posi- tion to boost or attenuate the corresponding frequency bands by up to 110d8 as shown in the figure below. The seven frequency bands are centered at 60H2, 150H2, 400H2, 1k{z, 2.4kHz, 6kHz and 1 SkHz. r00 1 k lok FREOUENCY lN (Hz) Octave control variation curves CH l0 8 66!4 w2(.nzo ?z!'+t6 610 @ RoaproR/TAPE oN/oFF swtrcH Depress this switch when listening to the tape deck con- nected to the rear panel TAPE terminals. In the ON posi- tion, only the signal from the TAPE PLAY terminals en- ters the equalizer. In the OFF position, only the signal from the EOUALIZER INPUT terminals enters the equalizer. @ EoUALIZER SWITCH o Press the right-hand EOUALIZER switch to compensate for the frequency response of the signals entering the EOUALIZER INPUT(E) terminals. The compensated signals are then made available from the EOUALIZER OUTPUT (F*ll terminals as the output signals. o Press both switches when recording signals which have been compensated by the SG-530. The compensated sig- nals are then made available from the EOUALIZER OUTPUT (F.;nl lsr.ntinsls and ADAPTOR/TAPE @ teminals. The same source signals are output at the ADAPTOR/TAPE r@ terminals as the signals entering the INPUT lE) terminals. When the front panel's ADAPTOR/TAPE switch is pushed to the ON position, the signals entering the ADAPTOR/TAPE @ terminals are made available at the OUTPUT (rill) terminals. Use this when connecting a second tape deck or connecting an adaptor component such as a mic mixing amplifier. When a tape deck has been rook connected, the front panel's ADAPTOR/TAPE switch func tions as a tape monitor switch. 2 2) OCTAVE CONTROLS il: .- - _---- llr:::- lElEl : j,, r*t IT"t- I| (rr*$ t*"*"^'*"'"I l:-l l-l l-l l-l l-l l-l l-l l-:-1 lrl l-l l-l l-l l-ll-l l-: " t-" ;:E=E=E-E=E=E=E=,=E=E=H=E=E=E=E= = '-''-''-''|-l l-l l-l l-l l- "-l l-l l-l l-l l-l l-l l-l l- " fnt 6 -t t_t t-t t- l||lL.: _l l_l l_l l_l l_l l-l l=l l_ i_' r-r r-r r-r r-r r-r r-, ,- - rsr uuuu-u-u-u-'"-Urli-ll-Ll-Url-Li-': I )POWER SWITCH (3) ADAPTOR/TAPE (4)EOUALIZER SWI ON/OFF SWITCH 150H2 4O0Hz 1k{z2.4kHz 6kHz
Page 2
2. SPECIFICATIONS Graphic Equalizer Section Equalizer Range (lndividual channel ad.iust) .110d8 60H2, 150H2, 400H2 , ikHz,2.4kHz,6kHz, 15kHz Total Harmonic Distortion (1kHz, All Control; Flat, Output: 1V) 0.005% Gain (Control: Flat) OdB Max. Output Voltage (1kHz, T.H.D.: O.O1Vo, Rg: 50kQ) Frequency Response . . 5Hz- ZOtHz+laA Signal-to-Noise Ratio (lHF A Network, short circuited, 1V Output) . . l00dB Inputlmpedance ...SOkohms Output lmpedance No more than 600 ohms 6V Miscellaneous PowerRequirements ....AC120V,60H2 PowerConsumption ..10W Dimensions . 420(W) x 97(H) x 216(D) mm 16-9/16(W) x 3-13/16(H) x 8-112(D) in. Weight (without package) 2.8k9, 6 lb 3oz Furnished Parts Connectioncordwithpinplugs ......2 Operating Instructions 1 NOTE: Specifications and the design subject to possibte modification without notice due to improvements. 3. BLOCK DIAGRAM LCH [- rN EQUALIZER/REC IEQI orrtA- f REc RCH r-tr{EOUALI ZER L- our t_ R€C TAPEL plav gff o'ru t Fn o,N ___i- EO REC POWER 6p Sl-3 Sl-2 Sr-r ,,>lWLt ! t--t 52 , uil TAPE I EO REC ONTAPE FOR SLIDE VOLUME KNOB LED NOTE: Push-button switches S1-i, S1-2 and S1-3 are locked independently. -6.5d B- -26.5d8V (at l kHz) -1 0d B- +1 0dB (at l kHz) 40OHz SIGNAL POLE lrHz SIGNAL POLE 2.4kHz SIGNAL POLE 6kHz SIGNAL POLE l5kHz SIGNAL pOLE R Chonnel ( Some os L Chonnel ) 5