Philips ax 2400 owners manual
This is the 4 pages manual for philips ax 2400 owners manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from philips ax 2400 owners manual (Ocr-read)
Page 1
English CONTROLS / POWER SUPPLY 12;......................switches the player on, starts or pauses CD play 2............................display 39.........................stops CD play, clears a program or switches the player off ∞.......................skips and searches CD tracks backwards §.......................skips and searches CD tracks forwards 4DBB .....................switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 5PROG...................programs tracks and reviews the program 6MODE/ESP..........selects the different playing possibilities: SHUFFLE , SHUFFLE REPEAT ALL , REPEAT , REPEAT ALL and SCAN, switch ESP on/off 7VOLUME +/- ......adjust the volume 8p/LINE OUT........3.5 mm headphone socket, socket to connect the player to another audio input of an additional appliance. 9OPEN ç............opens the CD lid 0HOLD...................locks all buttons RESUME .............stores the last position of a CD track played OFF ......................switches RESUME and HOLD off !4.5V DC...............socket for external power supply @............................type plate POWER SUPPLY / GENERAL INFORMATION Use only the AY 3162 adapter (4.5 V / 300 mA direct current, positive pole to the center pin). Any other product may damage the player. 1Make sure the local voltage corresponds to the power adapters voltage. 2Connect the power adapter to the 4.5V DC socket of the player and to the wall socket. Note: Always disconnect the adapter when you are not using it. Environmental information -All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into two materials: cardboard (box) and polyethylene (bags, protective foam sheet). -Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, exhausted batteries and old equipment. open You can use the following batteries with this CD-player: -normal batteries typeLR6, UM3orAA(preferably Philips), or -alkaline batteries type LR6, UM3orAA(preferably Philips). Notes:– Old and new or different types of batteries should not be combined. – Remove batteries if they are empty or if the player is not going to be used for a long time. Inserting batteries 1Push OPEN çto open the CD lid. 2Open the battery compartment and insert either 2 normal or alkaline batteries. Battery indication The approximate power level of your batteries is shown in the display. Battery full Battery two-thirds full Battery one-third full Battery dead or empty.When the batteries are dead or empty, the symbolA flashes, bAttis displayed, and the beep tone sounds repeatedly. Batteries contain chemical substances, so they should be disposed of properly. -Do not touch the lensAof the CD player. -Do not expose the unit, batteries or CDs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight). -You can clean the CD player with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. -To clean the CD, wipe it in a straight line from the center toward the edge using a soft, lint-free cloth. A cleaning agent may damage the disc! Never write on a CD or attach a sticker to it. -The lens may cloud over when the unit is moved suddenly from cold to warm surroundings. Playing a CD is not possible then. Leave the CD player in a warm environment until the moisture has evaporated. -Active mobile phones in the vicinity of the CD player may cause malfunctions. -Avoid dropping the unit as this may cause damage. Headphones AY 3806 -Connect the supplied headphones to the p/LINE OUT jack of the player. Note:p/LINE OUTcan also be used for connecting this set to your HiFi system.To adjust the sound and volume, use the controls on the connected audio equipment and on the CD player. IMPORTANT! Hearing safety: Do not play your headphones at a high volume. Hearing experts advise that continuous use at high volume can permanently damage your hearing. Traffic safety: Do not use headphones while driving a vehicle. It may create a hazard and it is illegal in many countries. Even if your headphones are an open-air type designed to let you hear outside sounds, do not turn up the volume so high that you cannot hear what is going on around you. CD player and CD handling Batteries (supplied or optionally available)
Page 2
GENERAL INFORMATION / CD PLAY Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage converter (4.5 V DC, positive pole to the centre pin) and the AY 3501 car adapter cassette. Any other product may damage the set. 1Put the set on a horizontal, vibration-free and stable surface. Make sure it is in a safe place, where the set is neither a danger nor an obstacle to the driver and the passengers. 2Plug the voltage converter into the cigarette lighter socket(only for 12 V car battery, negative grounding),then connect the wired end with 4.5V DC input socket on the set. 3If necessary, clean the cigarette lighter socket to obtain a good electrical contact. 4Turn down the volume and connect the cassette adapter plug to p/LINE OUT on the set. 5Carefully insert the cassette adapter into the car radios cassette compartment. 6Make sure the cord does not hinder your driving. 7Decease the volume on the set, if necessary. Start playback on the set and adjust the sound with the car radio controls. -Always remove the voltage converter from the cigarette lighter socket when the set is not in use. Note: If your car radio has a LINE IN socket , it is better to use it for the car radio connection instead of the cassette adapter. Connect the signal lead to this LINE IN socket and top/LINE OUT on the set. 4,5 V DC12 V DC In-car use (connections supplied or optionally available) CD PLAY / FEATURES -If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded properly,NF dISCis displayed, indicating that the CD has not been finalized. In that case, use FINALIZE on your CD recorder to complete the recording. -When playing a CD-Rewritable (CD-RW), please note that it takes 3–15 seconds after pressing2; for sound reproduction to start. -Playback will stop if you open the CD lid. -While the CD is read,1--:--flashes in the display. Volume and bass Volume adjustment -Adjust the volume by using VOLUME +/- on the cd player. Bass adjustment -Press DBB to switch the bass enhancement on or off yappears if the bass enhancement is activated. DBB DBB Playback information This CD-player can play all kinds of Audio Discs such as CD-Recordables and CD-Rewritables. Do not try to play a CD-ROM, CDi, VCD, DVD or computer CD. 1Push the OPEN çslider to open the player. 2Insert an audio CD, printed side up, by pressing the CD onto the hub. 3Close the player by pressing the lid down. 4Press2;to switch the player on and start playback. yThe current track number and elapsed playing time are displayed. -You can pause playback by pressing2;. yThe time at which playback was paused starts flashing. -You can continue playback by pressing2;again. 5Press9 to stop playback. yThe total number of tracks and the total playing time of the CD are displayed. 6Press9 again to switch the player off. -To remove the CD, hold it by its edge and press the hub gently while lifting the CD. Note: If there is no activity, the set will automatically switch off after a while to save energy. 0 Playing a CD Selecting a track during playback -Briefly press∞ or§once or several times to skip to the current, previous or next track. yPlayback continues with the selected track, and the tracks number is displayed. Selecting a track when playback is stopped 1Briefly press∞ or §once or several times to select the desired track. The track number is displayed. 2Press2;to start CD play. yPlayback starts with the selected track. Searching for a passage during playback 1Keep ∞ or §pressed to find a particular passage in a backward or forward direction. ySearching starts while playback continues at low volume. After 2 seconds the search speeds up. 2Release the button when you reach the desired passage. yPlayback continues from this position. Notes: – If the player is in SCAN mode (see MODE chapter), searching is not possible. – In shuffle, shuffle repeat all or repeat mode (see MODE chapter), or while playing a program, searching is only possible within the particular track. Selecting a track and searching