Onkyo TAR 22 Service Manual
This is the 13 pages manual for Onkyo TAR 22 Service Manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from Onkyo TAR 22 Service Manual (Ocr-read)
Page 1
SERIAL No. 3218
ONKYO SERVICE MANUAL
STEREO CASSETTE
TAPE DECK
MODEL TA-R22
Black and silver models
UDN, UDC, UD 120V AC, 60Hz
UG 220V AC, 50Hz
UW 120 or 220V AC, 50/60Hz
UQA, UQB 240V AC, SOHZ
SAFTY-RELATED COMPONETN WARNINGI! SPEC|F|CAT|ONS
COMPONENTS IDENTIFIED BY MARK A ON Track Format: 4 tracks, 2 channels
THE SCHEMATIC DIAGRAM AND IN THE PARTS Erasing System: AC erase
LIST ARE CRITICAL FOR RISK OF FIRE AND Tape Speed: 4.8 cm/sec.(1-7/8 i.p.s.)
ELECTRIC SHOCK. REPLACE THESE COM- Wow & Flutter: 0,07% (wms)
PONENTS WITH ONKYO PARTS WHOSE PARTS
Frequency Response: 20 7 15,000 Hz (30 7 14,000 Hz
NUMBERS APPEAR AS SHOWN IN THIS MANUAL.
i3dB) (normal position tape)
MAKE LEAKAGE-CURRENT 0R RESISTANCE 20 16,900 Hz?" 15,000 HZ
MEASUREMENTS To DETERMINE THAT EX- i3) 011% P°Sm°n tape)
POSED PARTS ARE ACCEPTABLY INSULATED 2° 17,000 "199 163000 HZ
FROM THE SUPPLY CIRCUIT BEFORE RETURN- 4 _ _ 3) (metal P951? mp9)
INC THE APPLIANCE TO THE CUSTOMER. Signal-to-Nmse Ratio: 1:81:13 (316ml posmon tape, Dolby
01]
A noise reduction of 10dB above
SkHz and SdB at lkHZ is possible
with Dolby B NR. A noise reduc-
tion of 20dB at SkHZ is possible
with Dolby C NR.
Input Jacks: Mic jacks: 2
Input sensitivity: 0.6mV/
600 ohms
Input impedance: 2I7 kohms
Line IN: 2
Input sensitivity: 60mV
NKY ® Input impedance: 50 kohms
DIN in jack: 1
Minimum input level: 0.1mV/
l kohm
Input impedance: 2.7 kohms
_1_
Page 2
W
Outputs:
Motors:
Heads:
Power Supply:
Power Consumption:
Line OUT: 2
Std output level: SOOmV (OdB)
Optimum load impedance: over
50 kohms
Headphone jack: 1
Optimum load impedance: 8 -
200 ohms
DIN out out jack: l
Std output level: SOOmV (OdB)
Optimum load impedance: over
50 kohms
DC servo motor: 1
DC motor: 1
Rec/PB head: Special Hard Permalloy
Erase head: Ferrite
ACZZOV/SOHZ, 120/220V, 50/60Hz,
240V/50Hz, I20V/60Hz
23 watts
Dimensions: 435(W) x 112(H) x 258(D)mm
(17-1/8 x 4-7/16x10-3/16")
Weight: 4.5 kg. (9.9 lbs.)
0 Models for use with only an AC 120V power supply are
not equipped with 2 DIN terminal.
Specifications and external appearance are subject to
change without notice,
SERVICE PROCEDURES
1. Replacing the lamp
This unit used the lamp listed below,
Circuit No. Parts No. Description
PL601 210090 PL14V 150mA
Caution: Before replacing the lamp. Be sure to unplug the
2.
power supply cable.
Instruction resistance measurement
Connect the insulating-resistance tester between the plug of
power supply cord and chassis.
Specifications; 500V more than lOMQ
3.
Replacement of power supply cord
There are two power supply cord outlets on the strain-
relief. Insert them in prescribed direction to ensure safety,
AS-UC-3 (UD
wise and other types of cords should be inserted horizontal-
ly.
Power Supply Cord Power Supply Cord
3
length wise Horizontal
direction direction
Blank Skip Operation
When no signal is detected on the tape for more than 20
seconds during playback, blank skip functions just as the
song location function to locate the beginning of the next
song and then return the deck to the play mode. Blank skip
operates only when the blank skip switch is on. The same
blank tape detection circuit is used during both AMCS and
standard playback; the gain is changed depending on
whether AMCS or blank skip is being used.
IC BLOCK DIAGRAM
BA6229 (REEL MOTOR DRIVER)
tc- vczz w:
(P D
l J_
~®vzv
5
ow -@va
Logm Prs Driver 11/)
u m 3 i0 Voui?
'-®V27
|_._77_l
(3
END
NPLr ocnur W
lNl®dE§iDE©i0UlZJ§ 7 g
L L L L SIG?
77 7 7 7 7
H L H L REV
l t u L H row
' H 7H7 r V i BRAKE
HA12088NT
(DOLBY NR IC ZCH in one package)
am sic IN V 1.: imam
_ ,
GND 7 2 Li..-LLhREC.lN
an» Pa in -J softens)
c Nigh
mm as: - a 39* in. Ham 7 flEtzwghtDPENi
:Mi # muons *5 iaJmPswro <
renew
s :7 -ma :LOWIGND)
err: LOW
(we 7 36
(RehFllNDl#B 35-lit" RBJNG)
at» amour g s _' it» Email!
lllllllllll
Rm armourazi t- Lch art our