Motorola pp 205 c service manual

Page 1

stereo MANUAL 68P63OIOA7O

MODELS PP205C, 206C
CHASSIS HS-2347B

MOTOROLA

M service manualJ

f;
MODEL PP205C MODEL PP206C
LOAD - Always operate the ampli- 4, Lift right side of changer up and
ELECTRICAL SPECIFICATIONS fier with an output load (either the position the other retaining clip ina
speakers or an 8 ohm, 5 watt re- vertical plane.
Power Supply: 120 volts, (:0 cycle sistive load) across each channel.
AC only 5, Lift up changer and disconnect
' SPEAKER PHASING - Refer to the audio andpower cables from changer
Power Consumption: 35 watts. schematic diagram. base plate.
a U n RECORD CHANGER REMOVAL CHASSIS REMOVAL
:1 o : RELATED PUBLICATIONS REFERENCE
9 g m 1. Open changerdrawertooperating 1. From rear of cabinet, remove
3 J 2 RECORD CHANGER . . . . MllzRC position, four (4) screws along rear ofhanclle
E 3 I and four (4) screws across cabinet
~42 N m 2. Screw changer hold down screws back,
" 9' '3 l k ise)£ ll into recordchan er
< m m SERVICE N TE (c N W M g
g 3 < o S base. 2. Remove three (3) control knobs,
4 -I 1 LINE CORD REVERSAL- For mini- Carefully pull cabinet front forward
2 n U o
o mum hum, insert line cord plug in 3 Remove 39:31 plus from right and remove three (3) screws which
2 both positions. Leave intheposition Side W311 Of record changer com- secure chassis to cabinet front.
that provides minimum hum, partment. Insert a screw driver
9 in the hole and position retaining 3. If necessary, disconnect all
'52 OPERATING AMPLIFIER WITH clip in a vertical plane. cables (speakers, etc_)_

MOTOROLA INC.
PART NO. 63P630IOA70 6-66

9401 WEST GRAND AVENUE, FRANKLIN PARK. ILLINOIS
PRICE I5 CEMSJM PRINTED IN U.S.A.

Page 2

STYLUS REPLACEMENT
To Remove Stylus

1. Lift tone arm to a vertical posi-
tion.

2., Rotate the stylus selector to the
78RPM position,

3. Grasp stylus with fingers and with
a gentle motion twist stylus so the
tip end raises and the rear portion
snaps out from under the retaining
clip.

To Replace Sty|us

1. Lift tone arm to a vertical posi-
tion.

2. Holding new stylus in position
with fingers, snap rear portion of
stylus under the retaining clip.

3, Be sure stylus rests in V" of
cartridge; then return tone arm to
normal position,

R1 0 1-M4732 C2
LT PRE AMP

LT VOLUME

T2 RT QZ-M4732

OUTPUT LT PRE AMP C11 CT

urn-m In!

STYLUS REPLACEMENT

mus mm!
In um mm"

IlmIII cm

CARTRIDGE REPLACEMENT

1. Pull metal retaining clip forward
and carefully remove cartridge from
holder.

2. Disconnect four (4) phonograph
leads from rear of cartridge.

R14 Q3-M4732
LT DR! VER

TONE

Q 6-M4872

PARTS LOCATION

REPLACEMENT
NUMBERS:

STYLUS PART

Diamond Stylus - 9Z-294DS
Sapphire Stylus - 92-29455

RTOUTPUT R16 E4 C10 RTDRIVER 06

R19 C3 T1
RT VOLUME LT OUTPUT

O4-M4732

Q 5-M4872
LT OUTPUT