McIntosh MHT 200 Brochure

Page 1

For the Consumers Protection: In order to ensure the highest level of customer satisfaction, newMcIntosh products may only be purchased over-the-counter or delivered and installed by an Authorized McIntosh Dealer. McIntosh products that are purchased over the Internet, by phone or mail order are presumed to be usedand do not qualify for any McIntosh Warranty. McIntosh does not warrant, in any way, products that are purchased from anyone who is not an Authorized Dealer or products that have had their serial number altered or defaced. MHT200 A/V System Controller & Optional Tuner FULL BANDWIDTH AMPLIFIERS McIntosh amplifiers are rated across the full 20-20,000Hz range… unusual in the home theater world. POWER GUARD ® Protects your speakers from clipping distortion on peaks using a patented light-beam-triggered circuit. NEW SILENT-SWITCHING Surround modes and inputs are controlled by new silent switches. NEW VOLUME CONTROL This fourth-generation volume control is progressive and noise free. SELF CALIBRATING Sit back and let the MHT200 set its own speaker levels and delay times with the supplied microphone. 96kHz PROCESSING Get improved sound from the newest 96kHz high resolution CDs and DVDs. 03.04.MHT200.20k 35005700 McIntosh Laboratory, Inc. 2 Chambers Street, Binghamton, New York 13903-2699 Tel (607) 723-3512 - US Toll-Free (800) 538-6576 - Fax: (607) 724-0549 - www.mcintoshlabs.com RATED POWER BAND: 20Hz to 20kHz TOTAL HARMONIC DISTORTION:0.05% maximum harmonic distortion at any power level from 250 milliwatts to rated power per channel. FREQUENCY RESPONSE:+0, -0.25dB from 20Hz to 20kHz +0, -3.0dB from 10Hz to 100kHz SENSITIVITY:1.0V A-WEIGHTED SIGNAL-TO-NOISE RATIO:92dB (112dB below rated output) INTERMODULATION DISTORTION:0.05% maximum if instantaneous peak output does not exceed twice the output rating per channel. OPTIONAL TM-1 TUNER FM SECTION SPECIFICATIONS USABLE SENSITIVITY: 14dBF which is 1.4µV across 75 ohms 50dB QUIETING SENSITIVITY:Mono: 19dBF which is 2.4µV across 75 ohms Stereo: 35dBF which is 15µV across 75 ohms SIGNAL-TO-NOISE RATIO:Mono: 75dB Stereo: 70dB FREQUENCY RESPONSE:Mono: +0, -1dB, 20Hz to 15kHz Stereo: +0, -1dB, 20Hz to 15kHz INTERMODULATION DISTORTION:Mono: 0.25% Stereo: 0.45% CAPTURE RATIO: 1.2dB PERFORMANCE SPECIFICATIONS PREAMP SECTION FREQUENCY RESPONSE (L/C/R/LS/RS/LB/RB) +/-0.5dB from 20Hz – 20kHz (Sub)+/-0.5dB from 20Hz – 140Hz This channel has an electronic low pass filter with an 80Hz corner frequency and 24dB per octave roll off in all modes except external. OUTPUT IMPEDANCE: Less than 560 ohms all channels MAXIMUM VOLTAGE OUTPUT: 8V TOTAL HARMONIC DISTORTION: All channels, 0.05% from 20Hz to 20kHz SENSITIVITY:Line Level: 100mV IHF Dolby Level: 200mV input External Input: 200mV for 2.0Vrms A-WEIGHTED SIGNAL-TO-NOISE RATIO:All outputs greater than 90dB below reference level. MAXIMUM INPUT SIGNAL: Analog Input: 6Vrms POWER AMPLIFIER SECTION POWER OUTPUT ZONE A:Minimum sine wave continuous average power output per channel with specified number of channels operating is: Rated Power Band (80Hz to 20kHz) into a 4 ohm load: 2 x 160 watts 3 x 140 watts 5 x 130 watts 6 x 120 watts POWER OUTPUT ZONE B:Minimum sine wave continuous average power output per channel with both channels operating is: Rated Power Band (20Hz to 20kHz) into a 4 ohm load: 2 x 150 watts OUTPUT LOAD IMPEDANCE:4 to 8 ohms. ALTERNATE CHANNEL SELECTIVITY: 75dB SPURIOUS REJECTION: 100dB IMAGE REJECTION: 75dB AM SECTION SPECIFICATIONS SENSITIVITY:20µV external antenna input SIGNAL-TO-NOISE: 48dB at 30% modulation 58dB at 100% modulation HARMONIC DISTORTION: 0.5% maximum at 50% modulation FREQUENCY RESPONSE: 50Hz to 6kHz NRSC ADJACENT CHANNEL SELECTIVITY: 45dB minimum IHF IMAGE REJECTION: 65dB minimum from 540 to 1600kHz IF REJECTION: 80dB minimum GENERAL OVERALL DIMENSIONS (H x W x D includes knobs and feet) 9-7/16" (23.97cm) x 17-3/4" (45.09cm) x 20-1/8" (51.16cm) WEIGHT:73 lbs. (33.1Kg) net 87 lbs. (39.5Kg) boxed