Mcintosh c 2200 service manual
This is the 48 pages manual for mcintosh c 2200 service manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from mcintosh c 2200 service manual (Ocr-read)
Page 1
:w C2200
TUBE PREAMPLIFIER
_.
n
mm __
in so do an 3 4n n
..,
mm Lkm
In fig man .20 .m a
a
mum Lnu
mtlninsh
c2200 was onlAwunsn
2 1» -£_ fi>
J I PHD as v/
«:7 LEE U I: a [Q
CONTENTS
Balanced Schemafil: and PCB .
Tone Schematic and PCB
Data Schematic and PCB .
Pushbulton Schema: and PCB 35 - 36
Performance Specifications 2
2
3
3
4 - 6 Meter Lamp Schematic and PCB 35 , 35
7 s
- 2
a
Nuxes .....
Rear Panel ,
Section anafian
Block Diagram ,
lnterconnectiun Diagram
Main Schematic and PCB
Display Schemafic and PCB
29-32
31»32
33x34
Pans Lisl..... 37 - 42
Exploded Views and Pans Liss 43 V 45
Repacking Instruction 47
SERVICE MANUAL
Page 2
PERFORMANCE SPECIFICATIONS
Frequency Mneme
+0, -05dB from 20sz 20.000141
Total Harmonic Dislnru'on
008% from 20Hz m 20,000HZ
Signal To Noise Ratio
Phone. ZOdB
High Level. 93dB
Maximum Voltage Output
SVn-ns Unbalancod. 16Vrms Balanced
Output Impulnnm
250 ohms Unbalanced, 500 ohms Balanced
Sensitivity
Phcno MM. 4.4mV for 2.5V rated Output
High Level. 450mV for 2.5V rated output
hipulmpedance
Phone MM. 47k ohms. 65pF
High Level, 22k Unbalanced. 47k Balanced
Maximum Input Signal
Phone MM,50mV (3 1.000111
High Level. 5V Unbalanced. 10V Balanced
Power Requirements
lOOVolLs, 50/601-[2 at 70 watts
110 Volls, 50/60Hz a! 70 watts
120 Volts. SWSOHZ at 70 watts
220 Volts. 50/sz at 70 watts
230 Volts. 50/60Hz at 70 watts
240 Volts. 50/60Hz at 70 watts
Nmz: Ref :0 m: rear panel of th: C2200 far m: mm: voltage.
'lhheComplimem
Phone Circuitry:
2 - I2AX7A
2 - HAT/A
HighlevelCirwiu'y:
2»12AX7A
2- l2AT7A
Overall Dimensions
17- [12 inches (44,5cn1) W. 7-5/8 inchcs (19.37cm) H. 20
inches (,5c1n) D (including clearance for connectors)
Weight
26.75 pounds (1214) net. 47.75 pounds (21 .67kg) in
shipping canon
NOTES
. The heavy lines on the schematic denote the primary
signal path.
, Unless oLherwise noted. all voltage: indicated on the
schematics are measured under the following conditions:
a. AC input at 120 volts. 50/60Hz.
b. All voltages are +/-10% with respect to ground. A
high impedance (10 megaohm) voltmeter mus! be used.
4. On PC board drawings. Square pad indicates:
a. Polaximd Capacilm's ~ PosiLive
b Diodes , Calhnde
c. Olhexs , Pin 1
5. WARNING
Pans marked with the symbol have critical
chaxacterisfics. Use only replacement parts recom-
mended by the manufacturer.