Kenwood TK 2200 Service Manual

Page 1

TKA-NSZVEZOO KENWOOD

SERVICE MANUAL

© 2004-7 PRINTED IN JAPAN
351-8694-00 (S) 719

-CONTENTS -

GENERAL ............................................................. 2
.7 Antenna REALIGNMENT ..........................
(KRAZS: 09 DISASSEMBLY FOR REPAIR
CIRCUIT DESCRIPTION

TERMINAL FUNCTION

SEMICONDUCTOR DATA ............

COMPONENTS DESCRIPTION .

Knob (CH-SELECTOR) PARTS LIST .........
(K299318433) EXPLODED VIEw

PACKING ............. .
Knob (VOLUME) ADJUSTMENT ................................................... 23
IK29-9309-03) PC BOARD
TX-RX UNIT (X57-6880-XXI
SCHEMATIC DIAGRAM ................

Cabinet assv BLOCK DIAGRAM
(A02»388|-|3I(2CHI: K
(A02»3882-03II8CH): K2 LEVEL DIAGRAM
KSC-31 / KNB-29N / KBH-10 .
SPECIFICATIONS

. 39
..... BACK COVER

Knob (P'I'l') 4.
IK29-9308-03)

Photo is TK-2200 (K2 type).
Does not come with antenna.
Antenna is available as an option.

Page 2

TK-2200

GENERAL

INTRODUCTION
SCOPE OF THIS MANUAL

This manual is intended for use by experienced technicians
familiar with similar types of commercial grade communications
equipment. It contains all required service information for the
equipment and is current as of the publication date. Changes
which may occur after publication are covered by either Service
Bulletins or Manual Revisions. These are issued as required.

ORDERING REPLACEMENT PARTS

When ordering replacement parts or equipment information,
the full part identification number should be included. This
applies to all parts, components, kits, or chassis. If the part
number is not known, include the chassis or kit number of
which it is a part, and a sufficient description of the required

PERSONAL SAFETY

The following precautions are recommended for personal

safety:

I DO NOT transmit until all RF connectors are verified secure
and any open connectors are properly terminated.

I SHUT OFF and DO NOT operate this equipment near
electrical blasting caps or in an explosive atmosphere.

I This equipment should be sen/iced by a qualified technician
only.

SERVICE

This radio is designed for easy servicing. Refer to the
schematic diagrams, printed circuit board views, and alignment
procedures contained within.

component for proper identification.

Factory default CH setting

RF power output

151.7750MHZ
151.8650MHZ
151.8950MHZ
151 .9250MHZ
152.7000MHZ
154.4900MHZ
154.5150MHZ
154.5275MHZ
154.5400MHZ
154.6000MHZ
154.6550MHZ
158.4000MHZ
158.4075MHZ

TK-ZZOO
Destination Number of CH Frequency No. / Frequency

CH1 151.625OMHZ CH15
K 2 channel CH2 151.9550MHZ CH16
CH3 154.5700MHZ CH17
CH4 154.6000MHZ CH18
CH5 151.7000MHZ CH19
CH6 151.7600MHZ CHZO
*CH7 151.8200MHZ CH21
*CH8 151.8800MHZ CH22
K2 8 channel *CH9 151.9400MHZ CH23
CH10 151.5125MHZ CH24
CH11 151.655OMHZ CH25
CH12 151.6850MHZ CH26
CH13 151.715OMHZ CH27

CH14 151.7450MHZ

CH1:
CH2:

154.5700MHZ / OT 67.0Hz
154.6000MHZ / OT 67.0Hz

CH1:
CH2:
CH3:
CH4:
CH5:
CH6:
CH7:
CH8:

154.5700MHZ / QT 67.0Hz
154.6000MHZ / QT 67.0Hz
151.7000MHZ / OT 67.0Hz
151.7600MHZ/ OT 67.0Hz
151.8200MHZ/ QT 67.0Hz
151.8800MHZ/ QT 67.0Hz
151.9400MHZ/ QT 67.0Hz
151.5125MHZ/ QT 67.0Hz

2W

*Note : Due to FCC regulations, these frequencies transmit at only 1 watt