Kenwood TK 2160 Service Manual

This is the 42 pages manual for Kenwood TK 2160 Service Manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.

Page: 1 / 42
Kenwood TK 2160 Service Manual

Extracted text from Kenwood TK 2160 Service Manual (Ocr-read)


Page 1

TKA-NSZVI 60 KENWOOD

SERVICE MANUAL

© 2003-8 PRINTED IN JAPAN
351-8652-00 (S) 1214

-CG\ITH\|TS-

GENERAL ............................................................. 2
SYSTEM SET-UP ................ ..2
OPERA11NG FEATURES ..3
REALIGNMENT .......................... ..4
DISASSEMBLY FOR REPAIR .. 5
(my; Option) CIRCUIT DESCRIPTION
INSTALLA110N ................
TERMINAL FUNCI'ION .......
Kn°b (CH-SELECTOR) SEMICONDUCTOR DATA ..

(K29-928013)
COMPONENTS DESCRIPTION

PARTS LIST ...................................
KnOb (VOLUM E) EXPLODED VIEW...
(9927843) PACKING ................ .
AD] USTMENT ...................................................
PC BOARD
Cabinet assy Tx-Rx UNrr (X57-672X-XX)
(A02-3826-33) SCHEMATIC DIAGRAM ................
, IBM-m BLOCK DIAGRAM ..
x.» 3; LEVEL DIAGRAM
IGC-30 ....................
SPECIFICATIONS

Knob (Pi-r)!-
(K294327903)

Dos not come with antenna.
Antenna is available as an option.

Page 2

TK-216O

ENERAL/SYSTEMSEFLP

INTRODUCTION
SCOPE OF THIS MANUAL

This manual is intended for use by experienced technicians
familiar with similar types of commercial grade communications
equipment. It contains all required service information for the
equipment and is current as of the publication date. Changes
which may occurafter publication are covered by either Sen/ice
Bulletins or M anual Revisions. These are issued as required.

ORDERING REPLACEMENT PARTS

When ordenng replacement parts or equipment information,
the full part identification number should be included. This
applies to all parts, components, kits, or chassis. If the part
number is not known, include the chassis or kit number of
which it is a part, and a sufficient description of the required
component for proper identification.

PERSONAL SAFEI'Y

The following precautions are recommended for personal

safety:

. DO NOT transmit until all RF connectors are verified secure
and any open connectors are properly terminated.

. SHUT OFF and DO NOT operate this equipment near
electrical blasting caps or in an explosive atmosphere.

- This equipment should be serviced by a qualified technician
only.

SERVICE

This radio is designed for easy servicing. Refer to the
schematic diagrams, printed circuit board views, and alignment
procedures contained within.

Unit
Model TX-RX Unit Frequency range Remarks
& destination
TK-2160 K,M X57-6720-10 136~l74M HZ :1 4995M HZ
LOC : 50.4M HZ
SYSTEM SET-UP
M erchandise received
License and frequency allocated by FCC
Frequency range (M Hz) RF power Type

Choose the type of transceiver

TX/RX 136~l74 5.0W

TK-2160 (K,M)

Transceiver programming

A personal computer (IBM PC or compatible), programming

interface (KPG-22), and programming software (KPG-82D)

are required for programming.

(The frequency, TX power HI/LOW, and signalling data are programmed
for the transceiver.)

< - - ) YES KRA-22 or KRA-26
n n 7
Are you usr g die optio al antenna. 0 ti l t

NO

' ' YES KVC-17 or KV C-Zl
< A m h 7 )_.
re yOLl usrng the Speaker ICTOp one. S k r i r

NO

l Delivery )

(Option)