Kenwood RXDM 65 V Service Manual

Page 1

RXDEMGSVEH(K) INT1P( 02.9.2 5:49 PM «3? 1 K1

RXDM65VH/M65VN KENWOOD

SERVICE MAN UAL
(HM'VBSSMP'HN655M P'N) ©2002-8 PRINTED IN KOREA

BS1 -581 4-00 (K/K) 1897

Fronthass* f c: )

(810-)

.__ Cassette lid *

Jil (A53-)

rental:

up! Ionnd

\00

volume

Front glass *

/\ B10- Knob * '
K j ( ) (K29-) \

Knob *

(K29-)

_ © _Miniature phone jack
(E11-0399-05)
LW'W %mmmg
C l a)
Panel ass'y * -0
(A60-) l

* Refer to parts list on page 30.

In compliance with Federal Regulations, following are repro- KENWOOD Corp. certifies this equipment conforms to DHHS
duction of labels on, or inside the product relating to laser Regulations No.21 CFR 1040. 10, Chapter 1, subchapter J.
product safety.

DANGER : Laser radiation when open and interlock defeated. 700/0

. . . . . AVOID DIRECT EXPOSURE To BEAM.
Caution : No connection of ground line if disassemble -.

the unit. Please connect the ground line on
rear panel, PCBs, Chassis and some others.

ll # ll

Page 2

r\

RXDEMGSVEH(K) INT1P( 02.9.2 6:03 PM N? 2

RXD-M65V-H/M65V-N

CONTENTS / ACCESSORIES / CAUTIONS

Contents

CONTENTS / ACCESSORIES ..............
EXTERNAL VIEW ...................
DISASSEMBLY FOR REPAIR
BLOCK DIAGRAM ...........
CIRCUIT DESCRIPTION.
ADJUSTMENT .......................................................... 13

Accessories

INTERCONNECTION DIAGRAM
PC BOARD ........................
SCHEMATIC DIAGRAM.
EXPLODED VIEW
PARTS LIST .................... .
SPECIFICATIONS .................................................... 36

AM Loop antenna (1)
(T90-0852-05): v
(T90-0893-05): MM1 XE

Remote control unit (1)
(A70-1587-05): MM1XV
(A70-1588-05): E

AC Plug Adaptor (1)
(EO3-0115-05)

I coo DEBUG
nuan/un u
not: an nI)
DUCJODDDUO

FM indoor antenna (1)
(T90-0855-05): v
(T90-0877-05): MM1 XE

Use to adapt the plug on the
power cord to the shape of the
wall outlet.

(Accessory only for regions where
use is necessary.)

SYSTEM CONFIGURATIONS

SYSTEM MAIN UNIT DESTINATION SPEAKER
HM-V655MP-H RXD-MGSV-H EMX LS-M65V-H
HM-V655MP-N FtXD-MGSV-N v LS-MGSV-N
Cautions

Operation to reset

The microcomputer may fall into malfunction (impossibil-
ity to operate, erroneous display, etc.) when the power
cord is unplugged while unit is ON or due to an external
factor. In this case, execute the following procedure to
reset the microcomputer and return it to normal condi-
tion.

0 Please note that resetting the microcomputer clears
the contents stored in and it returns to condition
when it left the factory.

Unplug the power cord from the power outlet, then while
holding the POWER or 0) key depressed, plug the power

cord again.
(5 POWER
or
2 @I 3 EU
I standby/timer . standby/timer %D

After resetting the microcomputer, the display will show
as follow:

The marking of products using lasers (For countries otherthan U.S.A., U.S.-Mi|itaw and Canada)

CLASS 1
LASER PRODUCT

The marking of this product has been classified as Class 1. It means
that there is no danger oi hazardous radiation outside the product.

Location: Back panel

CAUTION
VISIBLE LASER RADIATION

WNEN OPEN. no Nor STARE

INro BEAM on vIEw DIRECTLY
WITH oPrIcAI. INSTRUMENTS.

Inside this laser product, a laser diode classified as Class 3A laser
radiation is contained as alerted by the internat caution label shown
above. Do not stare into beam or View directly with optical instruments.

Location: CD laser pick-up unit cover inside this product

fii