Kenwood KEC 202 Owners Manual

Page 1

GOO/ANEDI

ELECTRONIC CROSSOVER NETWORK

INSTRUCTION MANUAL

DIVISEUR DE FREQUENCE

MODE DEMPLOI

AKTIVE FREQUENZWEICHE

BEDIENUNGSANLEITUNG

ELECT RONISCHE CROSSOVER NETWERK

GEBRUIKSAANWIJZING

CROSSOVER ELECTRONICO PER SISTEMI MULTICANALI

ISTRUZIONI PER LUSO

FlLTFlO SEPARADOR DE FRECUENCIAS ELECTRONICO

MANUAL DE INSTRUCCIONES

KENWOOD CORPORATION

Take the time to read through this instruction manual.
Familiarity with installation and operation procedures
will help you obtain the best performance from your
new electronic crossover network.

For your records

Record the serial number, found on the back of the unit,
in the spaces designated on the warranty card, and in the
space provided below. Refer to the model and serial
numbers whenever you call upon your KENWOOD dealer
for information or service on the product.

Model KEC-202 Serial number '

©PRINTED IN JAPAN BS4~Oi43-00(E)(MC)
92/121110987654321

Page 2

: C €
Illlilili

SAFETY PRECAUTIONS

A WARNING

Observe the following instructions to
prevent fires and personal injury.

0 When the Power supply lead, Memory
backup lead or Ground lead are
extended, use a 0.75 mm2 (AWG 18)
or larger automotive grade cable
which will withstand friction and heat
to safe guard against fires occurring
as a result of short-circuiting.

0 Make sure that metal objects,
particularly needles or coins do not
get into the unit to prevent short-
circuiting and fires.

0 If smoke comes out of the unit or a
strange smell is present, disconnect
the unit immediately and consult your
KENWOOD dealer. Continued use
under these circumstances could
cause a fire, as well as damage the
unit permanently.

A CAUTION

Heed the following instructions to keep
the unit in proper working order.

O The unit should be connected to a
12 V DC power supply with a minus
ground connection,

0 Do not open enclosures, such as the
front panel, top or bottom covers.

0 Do not place the unit, where it will be
exposed to direct sunlight or near
heating devices.

0 Do not dash water on the unit.

0 Do not place the unit in areas of
excessive dust, high humidity or on
unstable surfaces.

NOTE

0 If you have difficulty in installing the
set in your car, please contact your
KENWOOD dealer.

CLEANING

1. Turn the power off, before cleaning
the unit.

2. Wipe the front panel and other
exterior surfaces of the unit with a
soft dry cloth or a soft cloth lightly
moistened with a neutral detergent.

A CAUTION

I Do not use abrasive pads, thinner or
benzene (or other volatile solvents) to
clean the unit as this may remove
indicator characters.

Page 10

CONNECTIONS

Right input (red) RCA extension (optioriéi)

}(% %Center unit (optional)

(I.

Left input (white)

Rear high Rear high Hearmlddle Rear middle Front high Front high Frommiddl- Frantmlddle

Roulnut Laulpul R output Loutnut Routput LuuLpuz Ignition key switch
\

M01

Roar low
output
(Non-
fading)

For
left
outpur
(white)

A CAUTION

Output

Power control
output (blue/while)

Back up lead

(yellow) (43 Fuse
Fuse
Main fuse
IE! @
Ground lead 6 :31;
(black) 8 a)
Power control lead Batterv

(blue/whit!)

Power amplifier Middle frequency

(optional) front speakers

Power control lead

Power amplifier mquency

(optional) l front speakers

Power control lead

Power amplifier frequency

(optional) rear speakers
Power control lead

Power omplifier mquency
(optional) rear speakers
Power corIroTeadLU:

Power amplifier mquency

(optional) rear speakers

l Power control lead 3 _

Be sure to connect securely the power supply to the

power amplifier.

10