Kenwood KDCC 461 Owners Manual

This is the 16 pages manual for Kenwood KDCC 461 Owners Manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.

Page: 1 / 16
Kenwood KDCC 461 Owners Manual

Extracted text from Kenwood KDCC 461 Owners Manual (Ocr-read)


Page 1

KENWOOD '

KDC-C511
KDC-C461

COMPACT DISC AUTO CHANGER

INSTRUCTION MANUAL

CHANGEUR AUTOMATIQUE DE DISQUES COMPACTS

MODE DEMPLOI

CAMBIADOR AUTOMATICO DE DISCOS COMPACTOS

MANUAL DE INSTRUCCIONES

CHANGER AUTOMATICO DE CDs

MANUAL DE INSTRUQOES

KENWOOD CORPORATION

COMPACT

rflnee

menu. AUDIO

Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help
you obtain the best performance from your new compact disc
auto changer.

For your records

Record the serial number, found on the back of the unit, in the spaces
destgnated on the warranty card, and m the space provided below.
Refer to the model and serial numbers whenever you call upon your
KENWOOD dealer for information or service on the product.

Model KDCrCBl l/C461 Serlal number

©PRINTED IN JAPAN [56471092700 (K.El (MCl
99/2198/12lll09876543Zl

Page 2

Warning

The marking of products using lasers
(Except for some areas)

CLASS 1

LASER PRODUCT

The label is attached to the chassis/code and
says that the component uses laser beams that
have been classified as Class 1. It means that
the unit is using laser beams that are of a
weaker class. There is no danger of hazardous
radiation outSide the unit,

Marquage des produits utilisant un
laser {Sauf paur certaines regions)

CLASS 1

LASER PRODUCT

L'étiquette est attachee au chassis/boitier de
l'appareil et indique que l'appareil utiliser des
raynnc laser rte new: 1 Cela signifie que
lappareil utilise des rayons laser d'une classe
farble, ll n'y a pas de danger de radiation
accidentelle hors de l'appareil.

La marca del producto laser

CLASS 1

LASER PRODUCT

Esta etiqueta esta colocada al chasis/a la caia e
indica que el componente funCiona con rayos
ldeor dc claooo1.

Esto Significa que el aparato utiliza rayos laser
conSIderados como de clase débie No eXIste
el peligro de que este aparato erriita al exterior
Lina radiaCiOn peligrosa.

A marca dos produtos usando laser
(exceto para algumas areas)

CLASS 1

LASER PRODUCT

A etiqueta e presa no chassis/estojo e indica
que o componente utiliza raios laser,
classificados como sendo de Classe 1. Isto
signifian que. o anarelhn ecla insanr'ln rains laser
que sao de uma classe mais fraca. Nao ha
perigo de radiacéo malefica fora do aparelho.

2

ACAUTION

Use of controls or adiustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.

In compliance with Federal Regulations,
following are reproductions of labels on, or
inside the product relating to laser product
safety.

KENWOOD CORPORATlON
29673, lSHlKAWArCHO,
HACHIOJl-SHl

TOKYO, JAPAN

KENWOOD CORP CERT IES THIS EQUIPMENT
CONFORMS TO DHH5 EGULATIONS NO 21 CFR
T040. CHAPTER ,SUBCHAPTER J,

Location : Rear Panel

Fcc WARNING

This equipment may generate or use radio
frequency energy. Changes or modifications to
this equipment may cause harmful interference
unless the rnodlticatrons are expressly approved
in the instruction manual. The user could lose
the authority to operate this eqUipment if an
unauthorized change or modification is made.

This equipment has been tested and found to
Wiiipiy vvilll tire iiiiiiis {vi a Class B digital
device. pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
resrdential installation. this equipment may
cause harmful interference to radio
communications. if it is not installed and used in
accordance with the instructions. However.
there is no guarantee that interference Will not
occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures.

- Reorient or relocate the receiving antenna

- Increase the separation between the
equipment and receiver.

- Connect the eqmpment into an outlet on a
circuit different from that to which the receiver
is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

This Class B digital apparatus meets all
requirements of the Canadian interference-
Causing Equipment Regulations.

REMAROUE

Cet appareil numerique de la classe B respecte
toutes les exigences du Reglement sur la
mamnai hrnllillmlr (ii. (maria