Kenwood DPX 410 Owners Manual
This is the 56 pages manual for Kenwood DPX 410 Owners Manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from Kenwood DPX 410 Owners Manual (Ocr-read)
Page 1
KENWOOD
DUAL SIZED CD/CASSETTE RECEIVER
DPX-41 O
INSTRUCTION MANUAL
KENWUUU CUHPUHAI ION
COM PACT
[flee
DIGITAL AUDIO
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help
you obtain the best performance from your new CD/CASSEIIE
RECEIVER.
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below
Refer to the model and serial numbers whenever you call upon your
KENWOOD dealer for information or service on the product.
Model DPX~410 Serial number
(0 B64-1027-OO (KW)
Page 2
CO N T E N TS
.-"" "" ....... "" 4::
.WARNING ................ 3
.SAFETY PRECAUTIONS ---------- 5
.FEATURES OF DPX-41o .......... g
.OPERATIONS
ALL MODE .............. 10
FIE-TUNER MODE ............. 14
@TAPE MODE .............. 18
CD MODE ............... 24
e DISC CHANGER CONTROL MODE - - - - 28
E 2%; OTHER MODE ------------- 34
% REMOTE CONTROL MODE ------- as
CONNECTIONS ----------- 42
ACCESSORIES FOR INSTALLATIONS - - 44
REPLACING THE FUSE -------- 44
INSTALLATIONS ----------- 45
TROUBLESHOOTING GUIDE ----- 50
SPECIFICATIONS ----------- 54
The dIsplay iilustratIons appearing In thIs manual were created to augment the
explanatIons. These illustratIons may differ from the actual diSpIays.
Page 45
INSTALLATION (for Non-HONDA ACURA Car) l
e-----o
ACAUT 0N
When performing a check of the CD operation prior to installation, place this unit in a
horizontal position and perform a loading/eject of the CD.
I Installation
install onto the car bracket using the supplied screws (95 x 8 mm).
The number of screws to use will differ depending on the car model.
Accessory (2) \.,\
(M4 x 6 mm)
DPX-41O Car bracket
\
When a ground Wire lS included
in tne wrrino kit (which IS sold
separately), fasten the ground
wire With the binding screw
located on the rear panel of this
uni:
Accessow 6)
or Accessory in)
((235 x 8 mm)
Accessory (1)
(Only for NISSAN car)
ACAUTION
lll>idll such that the lllbldlldllUII dilglt-J of
this Jfill lS 30 {deg} or less. The somd
skipping may result if installed at an
dl uh: greater Lliail 30 [deg]. WlIhIn 5U [deg]
Page 51
m . fl -
Symptom Cause Remedy
Sound skips. -The installation angle 0 Adjust the angle to Within 30[degl.
exceeds 3Uldeg].
- The installation is not
stable.
. The (T) is scratched or
dirtv,
0 Tighten all screws
0 If skipping occurs at the. same
location even when the car is
stopped, the problem is With the
CD. See "Cleaning CDs (P.7) and
try cleaning Llie CD.
Sound quality is poor.
(Noise occurs during
playback.)
- The sound quality of this
particular Cl') is poor.
-The CD is scratched or
Oirtv.
The unit is in traCK random
Cannot get to the
desired track even
through track selection.
play mode.
0 it there is no problem when
olavino other CDs. then the
problem is with this CD.
0 See Cleaning CD5 (P.7)" and tw
cleaning the CD.
Cancel track random play mode.
Sound quality is poor
(sound is distorted.)
°Volume is too loud.
0 Heads are dirty.
I 0 The speaker wire is being
pinched by screw on the
car.
I Speakers have been Wired
incorrectly.
a The high temperature in
the car has caused the
internal temperature of
the unit to exceed 60 C
and this has activated the
protection Circuit.
- Use an appropriate volume level.
0 See Cleaning the tape head (P.6l"
and clean tho hoods.
- Check all speaker wiring.
0 Connect all speaker output
terminals to the correct speaker
terminals.
0 Lower the \rnliime and wait a
while until the temperature in the
car has dropped. The unit will
return to a normal operating
condition when the internal
temperature of the unit drops.
Contents of memory
are lost when the
engine key is turned
off.
Ratterv power is not >
connected to the prescribed
location.
See CONNECTlONS (P.42) and
connect correctly.
SRS effects are not
obtained.
0 Front speaker is not
connected.
0 The front output and the
rear output are connected
lfl reverse.
-The [grand aspeaker
terminals are connected ln
reverse,
- Fader and balance are set
all the wav to one side.
- Connect the front speaker.
' See "CONNECTIONS (P.42) and
connect correctly.
- See "CONNECTIONS (P.42) and
connect correctly.
t Adjust fader and balance.