Kenwood CD 2280 M Owners Manual 2

Page 1

KENWOOD

CD-2280MICD-2260M CD Changer Quick-Start Guide

In this guide well show

you:

How to use Simultaneous Dual-Room
Play and Continuous Play (CD-2280M)

* How to mute DTS CDs during
Continuous Play (CD-2280M)

How to enter disc and track names

* How to set up the VR-2090 receiver for
Dual-Room Play with the CD-228OM

Simultaneous Dual-Room Play (CD-2280M only)

The CD-ZZBOM has dual disc transports. Transport A plays through analog output A and the digital output;
transport B plays through analog output B. You can play discs on both transports at the same time for
Simultaneous Dual-Room Play.

To activate either transport,
press the front-panel
OPERATION button.

The A and B indicators above
the button will light accordingly

The players front-panel trans-
l 1 port controls will operate the
active transport

Continuous Play 1. Select
(CD-2280M only) Transport A

(see above)

34 Press CONTINUOUS PLAY
The display reads:
CONTINUOUS PLAY

Note:

" During Continuous Play
the same signal plays from
analog outputs A and B

By alternating between its two
disc transports, the CD-2280M
can play tracks continually with-
out any interruption between
tracks

2. Press PLAY,
or activate one
of the following

playback

modes: The digital output is not

All Disc used during Continuous

Random Play, Play

5W0? Play, DTS CDs that are muted
U510 ype ":.am 5:22: WW by the user {see next

Play, Best E 3 page) will be skipped dur-

se/ECW" Play ing Continuous Play so

that digital noise is not

aware comm um
nevus

sent through the analog
output

Page 2

CD-2280MICD-2260M CD Changer Quick-Start Guide

Muting DTS 005 During Continuous
Play (CD-2280M only)

DTS Multi-Channel Music CDs contain information that plays through
the CD-2280Ms digital output only,

To prevent digital noise from being played through the analog out-
puts during Continuous Play or when listening to music in Room B of
a Dual-Room installation, the user must mute" DTS»encoded 005
so that they can be automatically skipped

When playing DTS music CD5, make sure you have activated the
digital input on your receiver or decoder.

5t Use the 10-key pad
to select the disc

The display flashes:
C l'lLlTE DH
6. Press SET
The display stops
flashing and reads:
l'lLlTE Ell-l
7. Repeat steps 1-6 for

each DTS-encoded
CD

1 Press MODE
The display reads:
TITLE IHFUT

KENWOOD

2. Press DISC SKIP until
the display reads:

[1! ;. Fll-liilLEIE MUTE

3. Press SET /3

The display flashes:
MUTE D H

new: coanm. um!
name

4. Press SET again

The display stops flash-
ing and changes to:

SELECT [it

To Un-Mute a DTS CD:

Repeat steps 1-6, but after step 3,
press DISC SKIP. The display will
flash:

iiLlTE OFF
Then proceed with steps 4-7.

Naming Discs and Tracks

Discs can be given disc names (up to 25 characters),
and up to 20 tracks per disc can also be named (up
to 15 characters each).

Although the most convenient time to enter disc and
track names is when you insert the discs into the
player for the first time, (that way the player keeps
track of the disc names for you as you insert the
discs), you can use this procedure to enter or change
disc and track names any time you want.

These instructions explain how to enter disc names

when you insert the discs into the player for the first

time.

a Open the loading door and leave
it 0 en for this entire 0 eration

E Select an empty disc slot

Enter the disc mm The disc tray

ber directly on the will rotate so
10-key pad, that the slot is
in the loading
posrtion, and
Then press ENTER the display will
show the disc
OH' number:

Use the DISC SKlP_ T
buttons to select
the disc

Insert a CD in the empty slot. Make
sure the label faces towards our

right.

t mas
unE Gm a

mamas m