Jvc RX 805 VTN Owners Manual

Page 2

Rear Panel

0 Switch the power off when connecting any cables.

lama"

Ior Continental For the U K

Europe

For Au

For Canada
and other
areas

slialia

tint o mus N.

.e

0
0 rust
e

II n mum

®

nlhll rm

0 AUDIO terminals
(PHONO. CD. TAPE 1, TAPE 2, VCR 1, VCR 2)
. For audio Signal connection

0 Connect a turntable ustng a movtng magnet (MM) type
cartridge to the PHONO terminals

0 VIDEO terminals
(VCR 1. VCR 2)
e For Video signal connection

9 REAR OUT terminals
- To upgrade the rear speaker sound (to get more power),
connect an amplifier to these terminals.
In this case, disconnect the rear speakers from the REAR
SPEAKERS terminals, and connect them to the amplifier.

OMONITOR OUT terminals
- Connect the VIDEO INPUT terminal of a TV,
6 ANTENNA terminals

0 GND (ground) terminal

0 COMPU LINK-1 SVNCHRO terminals
7 Connect to units provided With COMPU LINK-l SYNCHRO
terminals for the COMPU LINK remote control function.

a Do not connect the remote cable to the JVC cassette deck
connected to the terminals other than TAPE 1.

0 AV COMPU LINK terminals
- These terminals are provided for connecting the AV COMPU
LINK to JVC AV COMPU LINK-compatible video components
to be marketed in the future.

0A0 OUTLETS (SWITCHED)

G FRONT SPEAKERS termlnels
0 REAR SPEAKERS terminals
9 CENTER SPEAKER terminal
G AM channel spacing switch
0 Fuse holder'

9 Voltage selector

9 Power Cord

' Not provided on units for Canada, the United Kingdom and Aus
tralia
" Not provtded on units for Canada, Continental EurOpe, the United
Kingdom and Australia.

Notes:

0 When connecting components, connect their left and right chan-
nels correctiv It channels are reversed, the stereo effect will be
degraded.

0 The AC OUTLETS do not supply power when the power swttch
IS turned off

0 Do not connect equipment requiring more than the outlet's rated
value.

Page 14

i.
l:
3;
l
l

'2'; S E A. Graphic Equalizer

The S.E.A. Graphic Equalizer breaks down the audible frequency
range into seven bands. Each band of tones can be adjusted as dis-
ired by the listener. Thus allowing you to make the necessary ad-
justments in the presicely appropriate frequency bands.

Vou can «mortise the sound to your taste.

'Youcenmecteubtlefrequencytoeutmeecouetlccherec-
terietlce of your Merino room.

You can compensate for the conditions of eudlo eqrdpmant.
Note:

The S.E.A. Graphic Equalizer does not work on the CENTER and REAR
speaker sound.

I Recalling a preset pattern

A total of 10 preset patterns can be used: 5 programmed preset pat-
terns. and 5 manual patterns which you create (SEA-A through E).

1. Press the SEA key.

In
ES!

The Dot Display normally shows the input signal levels.
It will change to SEA level for about 5 seconds when the SEA,
PRESET, LEVEL, FLAT, REVERSE, or FREQUENCY keys are pressed.

e': 2

.3.............................. g
«a:

as soccer-immune:

2. Call a preset pattern with the PRESET keys.

"" "":--".. e
..E 3
H u an II I. I." M
A-E: Manual patterns

Fl RAW: For music with a heavy beat.

8) EAR: For crisp, clear sound with transparent highs.
H) SOFT: For background music. at low volume level.
I) MOVE: For TV, VCR, and videodisc sound.

J) VOCAL: For music that is chiefly vocal, or speech.

Order

A)BDC>D>E>F>GDHDIPJblbacktothe
beginning)
0 After recalling these pattern, you can further change each

lrequerlcy band to suit yourself. However, since they are represen-
tative patterns, the original, stored pattern will be unchanged.

I Creating an S.E.A. pattern
1. Press the SEA key,

2. Press the FREQUENCY keys to call the desired frequency.
-11- "g

.3........"unirunnu..."

ii

3. Press the LEVEL keys to adjust the S.E.A. level.
.1m "0;

"Mmlillllfi

< ism. > t
e: enee-ue-u-u-iiunnun-u-
.1
iii

X: v05
\ 0' M M
Note:

When a frequency has been called, press the LEVEL keys while I
frequency is displayed (about 5 seconds). If the display is else
before you press the LEVEL keys, it can be recalled by pressing e"
FREQUENCY keys or LEVEL keys.

0 The SEA key enables you to compare the sound corrected
8. EA. with the original (uncorrected) sound during the pr- :.
for creating an S.E.A. pattern. Pressing the SEA key to turn 1
S.E.A. OFF lets you hear the uncorrected sound. When you i
the S.E.A. key again, the S.E.A. pattern being created is rectal
and the corrected sound can be heard.

0 To flatten the SEA characteristics.
" "3

In new stratum

Pressing the FLAT key while a pattern is yet to be preset will .,
it. Be careful not to press the FLAT key inadvertently.

e You can create an S.E.A. pattern using the remote control u '
1. Press the SEA CONTROL key on the external panel,

2. Use the Multi Function Cursor keys,

@
B~.~I
CE

-, + : Calls a frequency band to 0011'
A. V : Sets an S.E.A. level. '