Harman kardon hk 6650r amp

Page 1

The Harman Kardon

Model HK6650R

INTEGRATED AMPLIFIER

Manual 186A

Temniceal Mammal

narman. kardon mm

eeaaa

The following marks found in the parts list of this manual
identify the models as follows.
: North America area model Black version
: German model

: German model Black version
:lnternational model Black version
:Asia/Oceania model Black version

SPECIFICATIONS
LEAKAGE TEST .....
DISASSEMBLY PROCEDURES ..
POWER CORD REPLACEMENT
CONTROLS AND FUNCTIONS .....
GENERAL UNIT PARTS LIST.
GENERAL UNIT ..........................

CONTENTS

§Uml>bubf~ku

ALIGNMENT PROCEDURES
BLOCK DIAGRAM ......
P. C, BOARDS ............
ELECTRICAL PARTS LIST
SCHEMATIC DIAGRAMS
WIRING DIAGRAM ..............

harman/kardon

Parts and Service Office
240 Crossways Park West,Woodburv,N.Y. 11797
1112-0240A152 9129203 1500 Printed In Japan

H0999)IH

Page 2

HK6650R

SPECIFICATIONS

Nominal Limit Nominal Limit
RMS Output Power Tone Control Characteristics
so, 1 kHz THD 0.08% 105 w;1oow ®0®® Bass (at 50 Hz)
77.5 Wyow 6 Boost 10113:de
4Q,1kHzTHDO.1% 116Wg100W Cut 10dBi2dB
High-instantaneous Current Treble (at 10 kHz)
Capability (HCC) EUAgIOA €96©® Boost 10 dBiZ dB
72Ag65A 6 Cut 10dBt2dB
Half Power Bandwidth <10 Hz~1uo kHz <10 Hz~7u kHI Phase Correct Loudness
Frequency Response (at 50 Hz) 6 dBiS dB
(at - 3 dB down) 0.25 Hz~280 kHz <1 H1~2250kH2 Filters
3% Subsonic 15 Hz *3 dBii dB 63.3%
0.25 Hz~240kH1 <1 Hz~g200 kHz fig -6 dBii dB 963
Input Sensitivity DC Output Voltage
CD 135 mV 125 mV L channel 0 mViBD mV
Phono (MM) 2.2 mvxoa mV (336% R channel 0 mViGO mV
2.3 mV10.3 mV 0@ RIAA Equalization at Tape Out
Phono (MC) 130 uV120 pV ®®® (20 H1/20 kHz) (No load) +0.2 dBt0.5 dB/O dBi0.5 dB

Signal to Noise Ratio
CD

Phono (MM)
Phono (MC)

Channel Separation (at 10 kHz)
CD

Phono (MM)
Phono (MC)

140 pViZO uv o®

76 dagmdfi ®0@®
79 days :13 6

75ng65 :13 «neon;
78 d8g73 dB 6
73ng65 dB ®OQ®
76d8372 dB 6

Phono Over load (No load)
Phono (MM)
Phono (MC)
Dimensions (W x H x D)

200 ng160 mV
11 ng8 mV
17-1/2" X 5-1/4" X 1541/16
(443 x134 x 393 mm)

Weight 24.7 ibs (11. x.)
Power Supplies
North America area model AC 120, 60 Hz

International model

AC 230/240 V, 50/60 Hz

52 dB g 43 dB Power Consumption
54 dB g43 dB Nonh America area model 220 W (ZBOVA)
47 dB g43 dB ®G®® International model 250 W

IM Distortion Ratio
Damping Factor (at1 kHz)

60 dB £43 dB 6
0.027 %§0.1 %

75265 ®0®®
84-365 6

These specifications are service target specs.

Specifications and components are subject to change without notice.
Overall performance will be maintained or improved.

LEAKAGE TEST (FOR SERVICE ENGINEERS N THE USA)
Before returning the unit to the user, perform the following safety checks:

1.

l"

inspect all lead dress to make
certain that leads are not pinched
or that hardware is not lodged
between the chassis and other
metal parts in the unit.

Be sure that any protective de
vices such as nonmetallic control
knobs, insulating fishpapers,
cabinet backs, adjustment and
compartment covers or shieldsr
isolation resistor-capacity net-
works, mechanical insulators, etc.
which were removed for servicing
are properly reinstalled.

. Be sure that no shock hazard exists; check for leak-

age current using Simpson Model 229 Leakage
Tester, standard equipment item No. 21641, RCA
Model WT540A or use alternate method as follows:
Plug the power cord directly into a 120-volt AC
receptacle (do not use an Isolation Transformer for
this test). Using two clip leads, connect a 1500 Ohm,
10-watt resistor paralleled by a 0.15 uF capacitor, in
series with all exposed metal cabinet parts and a
known earth ground, such as a water pipe or con-
duit. Use a VTVM or VOM with 1000 Ohms per volt,
or higher sensitivity to measure the AC voltage drop
across the resistor. (See Diagram.) Move the resis-
tor connection to each exposed metal part having a
return path to the chassis (antenna, metal, cabinet,
screw heads, knobs and control shafts, escutcheon,
etc.) and measure the AC voltage drop across the
resistor. (This test should be performed with the
power switch in both the On and Off positions.)

TO EACH EXPOSED
METAL SURFACE OF
UNlTUNOER TEST

SIMPSON MODEL 229 ETC F
LEAKAGE TEST

HIGH GHOUN

OR

TO AC GROUND SUCH

D CONDUIT, ETC.

VOLTAGE LEAD
OF! + LEAD
VTVM
-0 AC SCALE 0-

15k!)
10W

TEST PROBE

T0 EXPOSED C
METAL PARTS

ONNECT TO KNOWN
EARTH GROUND

A reading of 0.35 volt RMS or more is excessive and indicates a potential shock hazard which must be corrected

before returning the unit to the owner.

AS WATER PIPE. BX CABLE