Gemini sound pmx 350 service manual
This is the 6 pages manual for gemini sound pmx 350 service manual.
Read or download the pdf for free. If you want to contribute, please upload pdfs to audioservicemanuals.wetransfer.com.
Extracted text from gemini sound pmx 350 service manual (Ocr-read)
Page 1
Page 2 21 1 2 3 6 5 4 16 9 7 8 10 13 11 1312 13 1917 14 18 19 20 15 26 21 22 2123 24 27 25
Page 2
Page 3 Introduction Congratulations on purchasing a Gemini model PMX -350 mixer. This- state-of-the-art mixer includes the latest features and is backed by a three year warranty, excluding crossfader and channel slides. Prior to use, we suggest that you carefully read all the instructions. Features - 2 Phono/Line Convertible, 1 Phono, 1 Line and 1 Mic input - Gain controls for each channel - Removable Crossfader - Cue Section Cautions 1. All operating instructions should be read before using this equipment. 2. To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified service technician. 3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove. 4. This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents. 5. When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit. 6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 7. DO NOT USE SPRAY CLEANERS OR LUBRICANTS ON CONTROLS OR SWITCHES. Connections 1. Make sure that the POWER (22) switch is in the off position. 2. This unit comes supplied with a 15 volt AC adaptor. Plug the male pin of the adaptor into the rear panel POWER JACK (6). Then plug the adaptor into a proper power source. 3. To connect the mixer to your amplifier, use the MASTER (1) jacks on the rear panel. 4. The unit is equipped with one microphone input. The MIC JACK (15) is a 1/4" (6.35 mm) and is located on the front panel. 5. On the rear panel are 2 stereo PHONO/LINE (3, 4) inputs, 1 stereo PHONO (5) input and 1 stereo LINE (2) input. The PHONO/LINE SWITCHES (8, 9) enable you to set the (3, 4) inputs to Phono or Line. The PHONO (5) input will accept turntable inputs only. A GROUND (7) screw for you to ground your turntables is located on the rear panel. The stereo LINE (2) input will accept any line level input such as a CD player or a cassette player. 6. Headphones can be plugged into the front panel mounted HEADPHONE (26) jack. Operation 1. POWER ON: Once you have made all the equipment connections to your mixer, press the POWER (22) switch. The power will turn on and the POWER LED (21) will glow RED. 2. CHANNEL 1: The GAIN (12) control allows you to individually adjust the gain of Channel 1. Switch (13) allows you to select PHONO 1 (5) or the LINE 1/PHONO 2 (4) inputs. CHANNEL SLIDE (14) controls the input level of this channel. 3. CHANNEL 2: The GAIN (23) control allows you to individually adjust the gain of Channel 2. Switch (24) allows you to select the LINE 2/ PHONO 3 (3) or the LINE 3 (2) input. The CHANNEL SLIDE (25) controls the input level of this channel.4. CROSSFADER SECTION: The CROSSFADER (20) allows the mixing of one source into another. The left side of the CROSSFADER is CHANNEL 1 and the right side is CHANNEL 2. The CROSSFADER in your unit is removable and, should the need arise, can be easily replaced. Crossfader units are available in two varieties: part RF-45 (which is identical to the crossfader supplied with this mixer) has a 45 mm travel from side-to-side, while the PSF-45 is equipped with a special curve designed for scratch mixing. To install a new crossfader: 1. Unscrew the outside FADER plate screws (B). Do not touch the INSIDE SCREWS (C). 2. Carefully lift the fader and unplug the CABLE (D). 3. Plug the new fader into the cable and place it back in the mixer. 4. Screw the fader to the mixer. 5. TALKOVER SECTION: The purpose of the talkover section is to allow the program playing to be muted so that the mic can be heard above the music. When the TALKOVER (11) button is pushed, the TALKOVER INDICATOR (10) will glow and the volume of all sources except MIC are reduced by -16 dB. MIC (17) controls the level of the talkover MIC. 6. CUE SECTION: By connecting a set of headphones (26), you can monitor either Channel 1 or Channel 2. Select Channel 1 by moving the CUE SWITCH (19) to the left. Move to the right for Channel 2. Use the CUE (18) control to adjust the headphone volume without affecting the overall mix. 7. DISPLAY: The DISPLAY (16) indicates the MASTER output left and right levels as controlled by the MASTER LEVEL (27). Specifications INPUTS: Mic....................................................................................1.5mV 600 Ohm Phono.......................................................................................3 mV 47 kOhm Line...................................................................................150 mV 27 kOhm OUTPUTS: Amp................................................................................0 dB 1V 400 Ohm Max............................20V Peak to Peak GENERAL: Gain (Channels 1 - 2)..................................................................0 to -20 dB Frequency Response...........................................20 Hz - 20 kHz +/- 2 dB Distortion...............................................................................................0.02% S/N Ratio.........................................................................better than 80 dB Talkover Attenuation.........................................................................-16 dB Headphone Impedance..................................................................16 Ohm Power Source.............................................................115V/15V AC 7.5 W 230V/15V AC 7.5 W Dimensions.........................................6.5" x 9" x 3" (165 x 221 x 85 mm) Weight...................................................................................3 lbs. (1.3 kg) ® In the USA: If you experience problems with this unit, In the USA: If you experience problems with this unit,In the USA: If you experience problems with this unit, In the USA: If you experience problems with this unit, In the USA: If you experience problems with this unit, call 1 (732) 738-9003 for Gemini Customer Service. call 1 (732) 738-9003 for Gemini Customer Service.call 1 (732) 738-9003 for Gemini Customer Service. call 1 (732) 738-9003 for Gemini Customer Service. call 1 (732) 738-9003 for Gemini Customer Service. Do not attempt to return this equipment to y Do not attempt to return this equipment to yDo not attempt to return this equipment to y Do not attempt to return this equipment to y Do not attempt to return this equipment to y our dealer our dealerour dealer our dealer our dealer . .. . .